SAJEEL

no one ?

Hi, have pelco dx8100 setup on static ip with remote client working fine on pc, has anyone been able to connect to a mobile client and what software have they used ? Thanks in advance

Hi there, Need some help again, i have a pelco 5100 dvr setup need to have remote viewing on pc and (mobile as well if possible). The customer seems to think it can be done on mobile although i am not so sure. From what i have gathered there is 2 connection methods, secure using a vpn connection which is endura network, and un secure the stand alone method. I have the wan ip, ip of dvr and remote key for software, i also have putty to ssh but cannot connect. I believe the software uses port 27235 but am not 100% on this, dont have any idea of port used for SSH I want to connect using remote client and normally i open the relevant ports on router and forward to dvr, install remote client and done. However on this dvr there is no where to choose port numbers, i will be using a dns resolver as they have dyanmic wan ip address. I am sure someone on here has setup these before and is able to help, thanks in advance.

RJ50 is the one looking for. This is serial connection for power and ptz controls.

Hi, Am looking to purchase 10 Pin RJ45 connector in the uk to wire up pelco ip cctv, but can only find one supplier; http://itm-components.co.uk/products/plug-rj4510x10rnd-cbl-100pk?utm_medium=cpc&utm_source=googlepla&gclid=CLvF1Yflg80CFbYV0wod7eYFHg Please let me know where you get yours from along with tool to crimp these ? Many thanks in advance.

the best option would be a mains power network adaptor, however this will not work if the socket ring is on different circuits, the other way is to use wireless-n ethernet bridge however there will a loss if you are too far from router, you did not mention distance from router as this will help offer solutions.

Thanks, do i download viewer app from play store ?

Hi, Anyone had any success on linking ip cameras to tv apart from using a pc or laptop connected to tv ? Any suggestions or ideas would be much appreciated

Thanks for replies, i decided to use a 16ch dvr as cost of 16ch multiplexer is almost the same, so i will remove 8ch dvr and 16ch then split outputs.

I have 3 dvr's 1= 8ch, 2=4ch 3=4ch They need to view all 16 cameras over 2 monitors and add a additional 2 monitor / tv to 1st floor. My solution is a muliplexer on dvr 1 and 2 output and feed 2 monitors by splitting output. Then take one more wire on dvr 3 to first floor and feed the other monitor. This way they have identical view upstairs / downstairs. I can use split screen or sequence to view 12 cameras. Any suggestions or better way to do this are welcomed ? Thanks in advance.

You need to know what port the application is using and then open that open that open on your router. this site will help you http://portforward.com/default.htm Then sign up for a dyndns account here http://www.noip.com/ you will install the client on pc on same network as dvr. If the dvr supports dyndns then you can enter details into dvr. Once all is done switch wifi off on mobile and test. An example of you address is http://homedvr.noip.com:1824 If your still stuck message me

yeh all set its been a long time since i spoke to you, keeping busy out there with cctv work ?

Hi Tom Good to see you still on the forum

sound like there is a lag in your broadband connection you can perform speedtest, http://speedtest.net/ make sure pc is in idle mode, no downloads or uploads. If you can connect to dvr but timesout then you have problem with connection, revert back to old isp or choose another isp, by the way what isp are you currently with.

if you post model and make of dvr i will try to help, in the settings of dvy most have different settings as well as h.264.