WebViewCCTV

Hi yes this is all set in the playback panel Regards

Hi I have a cctv system consisting of 4 Axis Cameras, 1 of which has audio built in, connected into a PC running Milestone Xprotect Essential. the shop has broadband and the images are viewed remotely in an office also with a broadband conenction. WIth live viewing of the images there is audio present, however, when switched to playback tab to view recorded images the sound disappears. However, when you download some recorded video and view it, the sound is present. Anyone seen these symptoms before? Thanks Mat

I should add that the images are being viewed using the Milestone Smart Client Thanks

Thanks for all your help. It was indeed firmware. As it was affecting 2 different types of camera i had kind of ruled it out and thought it was a PoE issue. Axis had to provide me with a firmware that hasn't been released. Glad it is sorted, but did cause me a bit of a headache! Thanks again Mat

Hi I am having some difficulties with a cctv system i have set up in a shop which has a broadband connection into it. I have attached a netgear fs116P to the router and into this i have plugged in 2 x Axis M3203 cameras and 2 x Axis M3204 cameras each plugged into the PoE ports of the switch. I also have 2 x Axis P3301 cameras that are plugged into the mains for power and into the normal ports of the switch for data. The system will be running fine for about 12 hours or so then one by one the cameras that are using PoE will stop transmitting images. I can still connect to the cameras in a web browser and can get into the settings page, but the live view has no images. If i reboot the cameras, then data is ok again, but it will stop again after about 12 hours or so. All the while the cameras plugged into the mains for power are ok for data and we can still view images. Is this likely to be power surges on the PoE switch? I am remote from the system at the moment so cannot view the leds on the PoE Switch All cameras are st up for H.264 compresed images. Any suggestions are greatly appreciated as i am tearing my hair out on this one. I have swapped out the switch from a FS108P to FS116P as i originally thought it was this that was faulty but the same thing is happening. I am now testing with 1 cam plugged into the FS108P and 3 into the FS116P to see if this makes a difference. I have previously set up a system with 3 x Axis M1054s plugged into a netgear FS108P and this is working fine Kind Regards Mat

I have the latest milestone device pack installed. Its not the software as if i connect to the affected cameras webpage, there are no images on it either, as though the camera is not processing any images. the camera is getting power and data though. Regards

Hi firmware is up to date - 5.12. I am also using milestone software, but its not that. If i connect another laptop to the network and browse to the webpage of the affected cameras, i can get to the page, but there are no images on the web page I get the same when browsing to the camera webpage from the PC running Milestone. I can get into the set up ok though. A reboot of the camera through the setup or removing the cat5 cable and re-inserting sorts the issue temporarily till it happens again! Its weird that the cameras are still on the network and getting power, but just are not transmitting images. One of the cameras has just gone down again, although i am not too sure if it is plugged into the fs108P or the FS116P. Is it likely to be power surges? It is a small shop with a lot of electrical equipment in it - fridges, display units, tills and more. If so is there any kind of PoE surge protectors? Cheers Mat

Hi thanks for your responses. I will upgrade teh firmware to see if this makes a difference. My thoughts are with the cameras drawing too much power or something along those lines. I am going to check with an electrician. Certainly there has been a very slight improvement with changing from a FS108P (32W max) to a FS116P (55W Max). But this has been from the cameras staying up for 8 hours to 12 hours. Not very good really!! I have previously installed a 3 cam system using 3 x Axis M1031s and PoE splitters plugged into a FS108P and this has run for months with no issues at all. I now have 1 camera plugged into the FS108P and 3 into the FS116P to see how this goes. Regards Mat