ChrisH
Members-
Content Count
45 -
Joined
-
Last visited
Community Reputation
0 Neutral-
ChrisH started following Looking for a good storage solution. DVR/NVR
-
Problem with door releasing when door is wiggled.
ChrisH replied to jmorin78's topic in General Access Control Discussion
Hmmmm. Quite strange. Does the door have a door contact? If so, this is also still in play. I have a hard time believing that it is the reader on it's own. If it does have a door contact, force the contact into whatever state it should be in when the door is closed by putting a jumper across the terminals in the panel. Now try your door again and see if it goes away. Maybe the door contact even wires to the reader some how. I've never seen that, but then again, I've never had what you are describing either. -
Not sure if you are trying to use this to track employees or their time, but be aware that using a card access system alone for time keeping not legal in the US. It must be a timeclock that acutally displays the time on it. Otherwise like the other posters said, any card access system can show history with just card reads.
-
James, How about another way to look at it. It sounds like you are really gung ho about installing, but have some worries. Why not save yourself the investment and work to your strengths? By this I mean, maybe you should try to set up a realationship with an electrician. You could sell the jobs, provide the smarts and the parts and pay the electrician to do the dirty work. He already has the tools and know how to get the job done. You can support the customers technical needs. I know a lot of guys that would not mind doing this type of work - the dirty part I mean. They just want to do what they know and get out. It takes a long time and a lot of mistakes to know about buildings and how they are put together and how to get to certain areas. There are also building codes to worry about, more so when you get into the commercial side of things. Either way, good luck.
-
Problem with door releasing when door is wiggled.
ChrisH replied to jmorin78's topic in General Access Control Discussion
You say you replaced the striker. Is this the electronic HES strike? If it is new, this problem occured with the old and new? Is there a door contact involved in this door setup? Either the strike is bad, the door contact is triggering something goofy at the panel, or the actual door hardware is releasing. What kind of door hardware does it have? Crash bar, 1/4 turn handle, paddle? -
Are you really going to have your kids dig a 18" deep trench 500'? That is going to take forever. You'd be money ahead renting a trencher. Depending on where it is, we often times knife the conduit into the ground. This is done with a trencher that has a vibrating blade on it. No dirt to shovel back into the hole. Not sure on the budget though. Directional boring will definatley be the most expensive, but least evasive. Good luck.
-
Please do not use 1/2" PVC. They should not even make the stuff. For the cost differerence (close to none) at least use 3/4". You would be more than ok with 3/4, but as Soundy said, bury two right away while the trench is open. Leave the second as a spare. Do not put more than 360 degrees of bend in the pipe and you'll be fine. As Soundy said, don't pull the wire as you go. It's much easier to pull it after, especially at that lenght. Also, I would pull an extra wire or two right away. At that length it will be tough going later to add anything. Also to make it easier you can get some Clear Glide, which is pulling lube. A little goes a long way and makes it sooooo much easier to pull in the plastic pipe. Lastly, if it were me I'd pull direct burial cable or indoor/outdoor rated cable in the pipe. You'd be amazed at how much water gets in the pipe over time due to condensation or a poor joint. The better wire will get you a longer life. Hope this helps. Good luck.
-
Do you mean all the wires per door are twisted, or all wires per panel? Either way, I'd rather keep them untwisted and manage the wire with tie wrap retainers and tie wraps. It helps tracing wires later when not all twisted together. Just my 2 cents.
-
No problem. I visited these guys at ISC West and they were very helpful there too. Nothing spectacular, but a decent low cost DVR. Especially for free, right Soundy! Glad I could help.
-
Motorcycle theft caught with video surveillance.
ChrisH replied to thewireguys's topic in System Design
Amazing what a few guys with a plan can take in four minutes! Did the store have any kind of burg system? Even if it did, four minutes is not much time, but just curious. They seemed pretty calm so I'm assuming that no loud sirens were going off during the ordeal. If that's the case, as burg system is a start. Possibly some sort of trackable asset tag on/in the bikes. Also the obvious things like making it harder to get in/out of doors. What I mean by this, is maybe something more secure than a double glass door for and entrance point. It was obviously easy for them to enter as there was not much of a deterant. -
Any idea how old it is? They have a five year warranty on them. I've installed a few of these and never had that problem before. If it's in the warranty, give them a call - 866-446-3595.
-
So can you tell me more about VideoIQ. I looked at their website enough to be curious. It appears that they make cameras with built in analytic engines, thus not needing VMS to do the processing. Do they also have local storage on the camera, via a SD?
-
Tom, those are interesting setups. The one that trasmits via 3G must use quite a bit of data streaming back to a remote site. Have you ever used either of these? I have given the mobile DVR a thought and transmit via GSM/3G for search and review. Anyone have experience with a cellular router?
-
Thanks Soundy. I did try to do some searches, but did not come up with much. Not using the correct key words probably. I think the distance will be too great to cover via a WLAN, thus I'm trying to look into other possible options or even other possible ideas. The customer will not be viewing on a regular basis, it will be more for searching and reviewing, but I do realize that this will still use quite a bit of data. Just exploring my options at this time.
-
I have done analog CCTV and some IP CCTV for more than a few years now. I was just asked to come up with a solution that I've never ran into. A customer wants a camera (type to be determined) at a remote site. This remote site has no electricity and what he wants to do is to watch a certain area durning mostly the daytime. Obviously this needs a solar/wind powered solution. The other problem is the DVR. Is there a way to remote into a DVR via GSM or are you stuck on going to the device and watching it locally? The distance is too far from his home to this site for a WLAN also. Like I said, this is totally new ground for me and any info or suggestions are welcome. Thanks
-
Elevator CCTV cabling problem.. Help!
ChrisH replied to missmimi's topic in Installation Help and Accessories
Soundy & tailbone, Thanks for the advise. As you mentioned the cat5e model that we were supposed to use is with stranded core. Can you advise which Belden cat5e comes with stranded core? Thanks again! Is there a reason that you do not want to work with the elevator company to get a pair of their wires which are already the correct type and in place??