![](https://www.cctvforum.com/uploads/set_resources_5/84c1e40ea0e759e3f1505eb1788ddf3c_pattern.png)
![](https://www.cctvforum.com/uploads/monthly_2019_01/V_member_2292.png)
vin2install
Manufacturers-
Content Count
505 -
Joined
-
Last visited
Content Type
Profiles
Forums
Calendar
Everything posted by vin2install
-
Anyone???
-
What model cameras are you using? is there sunlight where you are at? Are these all new cameras?
-
disconnect the hard drive. If the video comes back up then its your hard drive. If it stays the same then it probably is your DVR.
-
Cat5 Video Baluns with power
vin2install replied to avdesignoh's topic in Installation Help and Accessories
Any big CCTV distributor will have them in bulk. -
Maybe you should decrease your coverage to 15-17ft then you can see the license plate clearly.
-
how can I access private CCTV without password?
vin2install replied to yanaitat's topic in Security Cameras
lol -
Camera Interference caused by Switching Power Supply
vin2install replied to simyf's topic in General Digital Discussion
Your Power supply is probably defective. Get a new power supply. -
Dont see the BNC... need feed back
vin2install replied to Theodore's topic in Installation Help and Accessories
The previous installer was probably too cheap to use bnc connections and just spliced together some wires. Was probably held together by black tape. That is why you dont see the BNC. -
The 480TVL one. However you might have to get the correct lens though because the 1/4" has a narrower FOV
-
Yes you would use the BNC to RCA and that should do the job.
-
What is the model number of the LCD. Because usually 32 inches will have a fairly high resolution, on top of that it is probably widescreen. You can not realistically expect good quality when you focus on a single channel. Especially for a monitor that big.
-
PC Viewer D6 Series and Swann DVR4 Securanet - Cant see cams
vin2install replied to mostdef's topic in Computers/Networking
Sometimes it depends on your operating system too. I installed a capture card on a PC once and it would work on XP but it wouldnt work on Vista. -
lol i forgot to introduce myself too. I have been installing for 8 years now. Now i just repair CCTV cameras at my day job look forward to contributing to this forum. Vincent
-
Its because of the LCD monitor. To get the best performance you must match the output resolution with the native resolution of the monitor. Or you must get an upconverting monitor. But those tend to be real expensive.
-
What kind of camera is it? It looks like night time noise when the gain kicks in.
-
CRT's does not matter what resolution it inputs, it will still look good. However if the resolution of the output of the DVR does not match the native resolution of the LCD then your image will look terrible unless you have one of those high end up converting LCDs.
-
What is the cause of black horizontal lines going from the bottom to the top. This isn't the power supply as a new exact same model camera plugged in at the same place using the same source of power wont have these horizontal scrolling black bars. I'm thinking it might be because of the power draw of the LED's. Does anyone know what causes this?
-
I'm just wondering is it after a period of time does the camera start drawing more current?
-
24vac can also come in those kinds of connections too.
-
1/3" CCD's are generally more sensitive to light.
-
No it could be either one. Type of connection does not define if it is a 24vac or 12vdc
-
Hi i would like access to the Dealer forums too. Our company is always looking for new ideas and suggestions for our camera lines. Thanks Vincent Product Support Golden State Instruments Co.
-
problems again with ir camera
vin2install replied to kingo110's topic in Installation Help and Accessories
Circuits on the IR board are probably fried. Probably a surge of some sort that just happened. That is if the IR's are on all the time. -
Its not the camera lens thread ring that is loose its the Len's thread mount that is loose. This happens a lot.
-
So is the ground loop in the camera? And why does it do it when the IR's are on only?