gibbo

Goodmorning, I'm from Italy, where I can buy on Internet a Dahua IPC-HDB3200C ? Here in Italy is very expensive (300 dollars....). Thanks Andrea

Thanks for your answer ! I disabled the auto reboot because I thought it was cause of the problem, but it isn't.....

I have two cameras IPC-HDW4200S (firmware 2.420) and a NVR NVR 4104P (Poe) (firmware 3.2300.VT00.0.R). Cameras are connected both to the NVR integrated poe switch. After some days (5-7) both the cameras lose the connection. In the NVR log i can read the messages "REMOTE INFO" and the cameras starts to LOGIN and LOGOUT. Any suggestion ? Could be a firmware problem ? After a software reboot of the NVR the cameras start to work properly...

Check (and change if needed) IPV6 address of nvr and cameras. If identical then there might be a problem of conflict. Also, create and use a different account (reusable) to allow nvr to connect to cameras (user might be locked). Thanks. I use IPV4 and not IPV6. I have seen that before the problem starts, there is a shutdown of the nvr without any reason. The nvr is connected to a UPS power supply backup system. Any suggestion ?

Sorry but with NVR 4104P firmware v.3.200 the password of the 26-01 does not work....

Goodmorning, does someone has the user manual for Dahua NVR4104 ? Which port I have to open in my router ? Thanks Andrea

Someone has the last firmware for this NVR ?

It's some days that I have a message "SD memory not present" even if the memory is present and the camera stopped to record. Before this the camera worked perfectly. Do you have some suggestion ? I tried to reboot the camera without successful. Do you suggest to try to remove the SD from the camera and format it ? Unfortunately my camera is not very accessible.... Thanks Andrea

Where did you find it?

I can confirm that with RTSP it works much better than with TCP.., Thank very much for the help!

I didn't test RTSP.... Does it work well? Better than TCP?

Goodmorning, I need your help about the connection of my Dahua IPC-HBD3200C and IP Cam Viewer for Android. The connection is very slow (it takes too much to establish a connection). Do you have suggestion about the settings on IP Cam and on the Dahua ? Do you use the http connection or the TCP ? Thanks anArea (sorry for my english...I'm from Italy).

Thanks so much!

I have a Dahua IPC-HDB3200c and I use Ip Cam Viewer for Android to connect from my mobile. If I connect with the Pc the connection is very fast, but with Ip Cam Viewer is very slow even if I'm connected with the wi-fi. Which setting do you use with Ip Cam Viewer ? Which bit rate do you setup on the camera ? Thanks andrea

Thanks everybody!

Do you know where I can download the last firmware for the Dahua IPC-HDB3200c ? Thanks Andrea

Thanks a lot !

Thanks everybody for your helps ! Unfortunately amazon.it is expensive like to buy to a reseller. The only solution is buy in US or directly in China. One more question....what do you think about the camera IPC-HDB3200C ? I need to control my house access, so I have to check if a person is in front of my house door. Thanks Andrea

Have you tested the new firmware v2.0 ? I think that the intelligent analysis does not work properly......

I upgraded the firmware to the version v1.22 but I still have problems. Do you have suggestion to fix the problem ? Should be the memory of 32GB too big for the camera ? I'm using a Transcend 32GB class 10, could be a Sandisk a better solution ? Or the problem could happen after a power down of the camera ?

I've the Samsung SNO-7080R that's very close. It works very well but I've some problems with the SD: viewtopic.php?f=19&t=30178

Thanks a lot! I saw a new firmware released in August. I'll try it and I'd like test with the original SD of 4Gb. I let you know!

You should contact the manufacturer directly for tech support. I contacted the service but the gave me solutions that did not fix the problem. They told me to reduce the resolution and disable the "Smart Coedc" but as I thought nothing changed. When I arrive close to 3 GB of available space I receive the message "Data base corrupted"......

Could please someone help me? Thanks very much

Could please someone help me? Thanks very much