Siiak

We recently called on to bid for a job , it's a place of worship and got vandalised 4 time including damaged property, maybe related to current toxic politics, anyhow the place has hdtvi cams installed around the premises which did not capture good images in the very low light environment since the parking lights are programed to go off after mid night and some smaller lights are on. Can any of you guys have any recommendations for good IP cams which work well in very low light giving good pictures and also can try n capture a license plate or any other identifiable properties off the vehicle entering , leaving or individuals committing these crimes. Will appreciate any reliples or recommendations

Hi All, We are trying to finish a install, and have to incorporate 4 existing Hikvision cameras, we installed a 3rd part USB 4 port dongle, and are adding the hikvision as Onvif protocol, when adding 5.4.x firmware cameras no problem, but as soon as we try to add a camera with 5.5.x firmware the geovision software will crash and restart. Initially we though may be the cameras were defective, so we bought 2 more from local ADI, but the results were same, I contacted Hikvision support and they tried various settings but same results, so long story short they told us that Geovision has the issue in there software. Has anyone here on the forum faced similar issues is there like a patch available, I search geovision support forums but did not find any solution. Will appreciate any reply. Thanks

Hi all, Has anyone hooked up the geo data capture box with a VeriFone Ruby2 system to overlay the transaction data, the customer pole display is hooked to com3 which is a RJ45, I think the system is providing data and power to the pole display via the cable, I will appreciate if any one has a pin out configuration for a link where I can buy the premade cable . thanks

Hi all, have any one tried to watch the feed on VLC player with RTSP what is the command , I tried the RTSP command I found on Geovision forums site but it did not work, its the cloud based geovision camera Thanks

Hi All, I have a Aver NV6000 windows 7 based system how do I reset the supervisor password, in Geovision there is a password reset application which can remove reinstall password, is there anything similar on Avermedia too Thanks

No Still searching for a solution Geo was not a big help, please keep me in loop if u find a solution. Thanks We finally got it working. We had to change the baud rate to 1200 and data bit to 8 on the V3E. The port has to be configured on the Ruby 2 correctly as well....it has to be set to the DVR something...sorry...we use a petroleum service to set that part up so I can't help much there. If I get more info, I'll post for you. I will really appreciate your help, which com port dose the cable goto also the cable did you use a standard RJ45 to db9 straight serial cable or did you custom made it. Thanks

No Still searching for a solution Geo was not a big help, please keep me in loop if u find a solution. Thanks

make sure under webcam, you have enables mobile and 3gp

It will only work on IE or you can download the multiview application from geovision's website for android you have to download the app ipcam viewer it supports older version, u can try the lite version which restricts u to view 4 camers or for 3.99 get the full version go with 7.04 version that should work without a dongle regds siiak

Hi Fred, Did you ever find a solution ? Im stuck as well trying to capture from Pole display, any help

Hi, Im trying to connect Gilbarco passport Customer pole display which is serial to GV-NVR, I have configured everything correctly on NVR and can access the v3e box from NVR the V3e Sits between the passport edge port and pole display the pole display works fine so the data is passing. when I use the pos option from GV-nvr and map the camera no data comes in, but occationally like after 2 or 3 mins I get a 5 6 lines of advertisment from customer display thats about it. I really need some help thanks in advance

Im still looking for a solution Geovision was not very helpfull Thanks

We are doing a hybrid system for a client, where there will be 16 analogue and 5 IP, the card we selected is a GV-1240b, my question is do we install 2 cards or just 1 card, does the 8.5.5 software gives the option of intergrating this 16 analogue and 5 IP working togeather using 1 card, ? Thanks for any advice help

Yeah this is definately a card issue, as I remember going for a install and the customer did not had the software cd the card was 1480, since I had a 8.5 cd in my bag I installed that and it updated the firmware too, everything workied fine when I left next day the customer called again to say the system is doing funny thing and one of that was encoding issue with images, on a close examination we found that the card was a fake.

Hi all, How would I capture Gilbarco Passport data and overlay that to te IP camera, the store has two passport registers, in the analogue solution we just use AVE VSI with serial interface cable to the customer display pole. I would appriaite any help / solutions Thanks

Thanks for replie, I will be using geovision NVR and Geovision IP camera Thanks

Hi All, We are doing our first all IP install with 16 3MP geovision Dome cameras and Ver. 8.5 NVR, Dell Optiplex 790 i7, 4GB Ram, 2 x 1.5TB data Drives and one 80GB SSD boot Drive, 2 x 8 port srw208mp-k9-na POE Switchs. I would like to know if I should go with 32 bit or 64 bit windows 7, will 4GB memory be enough, how to tweek windows 7, how easy will it be to configure the NVR, any howto links would be appriciated. Thanks Siiak

Thanks a lot guys for your advice, Im hoping that the installation will go smooth I will post the results or questions if I will run into any hickups. Thanks again

Hi all, I need the latest firmware for the DVR the current version on the dvr is system 2.606.0000.0 Build Date 12-07-2010 Web 2.1.7.29 I will really appriicate if someone provide the update Thanks a million

We usually use The dell Optiplex Mini towers, great machines no headaches

The cheaper solution would be to use a multiplexer since GV-800 dose not have spot out with loop out, and run the output of the multiplexer to your spot monitor, the setup would be all camera output cables would go to multiplexer and the loopout from multiplexer would goto your geovision GV-800 card or you can use a geo DSP card

Hi all I would appriate if someone can help me, I have a 1480 card and was running ver. 8.3 everything was ok, I have a touchpro 2 from sprint and could watch the cameras from withing internet explorer and also on Iphone. I updated to version 8.34 and now on my touchpro if i want to connect it will connect will ask for username password, and I can select the camera to watch, but once I do the selection the phone loads windows media player to play the stream I think and I recive the following error streaming media invalid parameters to play media on my computer if i try the multiview after putting the login password, i just get the message trying to onnect to server. even on my i phone it stopped working I there something special i have to do in the new version of software. regds siiak

Hi, Yeah ports are correct as I can login from phone select camera it just at the last stage where the phone switches to the stream player, I get the error. I tried other windows mobile phones too but same results, I would appriciate any help

Hi all, I need help if anyone has a solution, the dvr is a DVMR Jpeg2000 based system and was installed in early 07, recently there was a robbery where the cleark got killed, the police got the video and the suspects were caught, the problem we r facing is it will burn on cds and will only burn 3 mins, worth of video it takes approx. 18 to 20 mins. to burn 1 cd. Is there a way or software were we can directly hook up the HDD computer and extract the video files for the whole week. I will appricate any replies. this picture of the dvr is attached Thanks Siiak

So the HDD can be hooked up to the windows computer ?, and can be treated just like any other External drive to move data ? regds Siiak