jjp2014

Okay the NVR is outputting component level audio (if you plugged just a speaker into the RCA jack little or Nothing will transmit) 1. Verify the HDMI extender requires pre-ampd send for XXX distance... 2. Why are you using a Y adapter... 3. Verify the the NVR audio output//Input are not muted. 4. Verify the Camera audio Output//input are not muted Test system on a bench: I would try a 5' piece of cable to jump the raw audio to HDMI extender TX-unit Use a patch cable from the HDMI extender-RX to HDMI-TX>>> did the video and audio pass... if not start with the basics then expand..

I PM'd op as well ... There are costs of doing business, I for one am learning the CALIFORNIA pinch... IRS, board of equalization (ca reseller), insurance, business Lic, federal security clearance, shipping, Certifications, product minimums, etc ... these things add up... Op wanted to know why he got high number quotes.. I would like to say, that I love what I do, I take pride in my work and Do the work the right way the first time..... Unlike most in my service area.... There are a lot of details however that are missing from Op.. Construction type, how long of a run, op own the property (rent, lease)....Existing door-bell, is the infrastructure there to support upgrade unit...(likely hood of a warranty call?) Nothing like the requests for a door-bell unit install " super simple...one story house kitchen i s where I want the Base...front door in where i want the remote at" upon further investigation: solid cement walls, poured concrete pad, and the existing door bell doesnt work....they want the job done for under $250.00 >>>

Here is the specs i Found... http://www.averusa.com/surveillance/products/hybrid-capture-cards/nv5000.asp

what is the firmware version that you are using.... has that been updated since upgrading the hardware?

Aiphone JK series requires a bit of BACK end programing ...not just run some wires.. I start out at $2,500 for a base and remote... Plus any additional custom work, covert cable snake, etc... Rough break down... $1200.00 - parts/ materials $800.00 - Labor $500.00 - Taxes, License, Insurance PM me see, Im located in San Rafael area.

Looking at running Milestone Xproject essentials as my NVR software.... Then looking at an I7 4 gigs of ram 1.5TB primary media drive and 250 Gig software drive Looking at a 750' run hardwire... -OR- Looking at wireless 5.8ghz bridge... PROS/ CONS?? HARDWARE: (5) Axis P3364-Ve domes (4) Axis Q1604 with 50mm telephoto lens system -Need case model that will fit this set-up What is the rule of thumb for IR and LPR? (within 50' from cam unit)

Looking at running Milestone Xproject essentials as my NVR software.... Then looking at an I7 4 gigs of ram 1.5TB primary media drive and 250 Gig software drive (5) Axis P3364-Ve domes (4) Axis Q1604 with 50mm telephoto lens system -Need case model that will fit this set-up What is the rule of thumb for IR and LPR? (within 50' from cam unit)

I am located just north of San Francisco, Ca.... I have a project coming up and need (3) LPR specific Cameras IP based.. and (3) General View IP outdoor Dome camera that is equivalent to the AXIS: P3364-VE 6mm They are using a Pelco NVR DSSRV-030-US >>>> Thank You

Did a Site walk through.... Main office to Guard shack ( really its a closet with irrigation controls, no windows ...) Total conduit run is just over 700' Main office to furthest camera at other drive way just over 650' Looking at Axis for my dome camera units (5) Model: P3364-VE Looking at two options for License Plate Reading units (4) >Option #1: Axis, Model: Q1765-LE >>Option #2: Messoa , Model: SCR510HB **Client wants Low profile high results from the license plate read Longest throw is 150' shortest throw is 30' Mid-range throw is around 50' ** Using a Pelco NVR

Just caught your PART B. On RJ45 connector you need to list what device your plugging into.... IE a active Balun, camera, etc the device will have a RJ45 Pin out then you just match the wire pair to the assigned pin location and BOUYEA!

Thank you for the reply, I "qualified" the network and POOOP! it failed all tests including continuity I am now looking into "nanostation m5" wireless bridge option.... Tentatively: (1) NVR unit -Pelco DSSRV-030-US [Main office] (run of Dual CAT6 - 1,650') from guard shack POE switch to Main office NVR 8-Port switch (A. Guard Shack) [Hybrid] >ZONE A: (2) Messoa-SCR515HB (LPR) -Driveway Enter/ Exit {Pelco: NET5402T} Analog to IP encoder (1) Axis: P3364-VE P/n:0299-031 (IP) -Generic shot of driveway (B. Main office) [ Hybrid] >ZONE B: (1) Axis: P3364-VE P/n: 0299-031 (IP) -Cover pool and spa deck area >ZONE C: (2) Messoa-SCR515HB (LPR -Driveway Enter/ Exit {Pelco: NET5402T} Analog to IP encoder (1) Axis: P3364-VE P/n: 0299-031 (IP) -cover generic driveway >ZONE D: (2) Axis: P3364-VE P/n: 0299-031 (IP) -Underground Parking garage drive way Enter/ Exit ____________________ So POE switch at Guard shack and at Main office ...... ? How I mapped it out: Main OFFICE: 8-Port Switch (with POE?) >ZONE A (Guard Shack): (Uses 3 ports of 4) 1 Port POE switch remain [port 4 to Zone A to Main office] >ZONE B: (Pool + SPA area) (uses 1 port of 6) 5 Ports POE switch remain >ZONE C: (Driveway LPR Cams + Dome) (uses 3 ports of 5) 2 Ports POE switch remain >ZONE D: (Garage Domes) (uses 2 ports of 2) 0 Ports POE switch remain DOES THIS MAKE SENSE? Am I missing anything? Looking at: (estimated) 3500' of 1/2 emt conduit 4,500' Cat6 Direct burial 1500' Cat6 Plenum ....... A lot of hours pulling cables and laying conduit.... CLIENT is already working on parking lot so hope the contractor will allow me to lay Underground cable path from guard shack to Main office! :D

http://www.zmodo.com/720p-full-hd-4ch-touch-screen-nvr.html this might be a sleeker install, only 7.5" touch screen >>>i have never used this model, just googled NVR with screen What is the application? Why does said client want a door monitor? do they want facial details? if not go Analog might be a bit of less headache, your going to have a Delay with IP cameras.... just the rest of my .02

http://www.ezcctv.com/product/Touch-O-577.htm I have used this a few times... mostly evidence rooms ....but usually I just take a spot out send to a monitor my .02

Yeah the electrical contractor ran a few thousand feet of cca on the job site, all had to be re-run! cost a pretty penny....

is the cat5 cable Copper clad, or CCA ?? because the wire is sooo brittle! Sorry to say it but you get what you pay for, its an expensive lesson! :/

I am working on a Police rescue boat, heavy wave action, hard slams and pitch, roll, Yaw effects on DVR unit. I have replaced 3 Hard-drives so far they started as standard laptop 350gig hard-drive, upgraded to Extreme use 500 gig HD, then upgraded the hard-drive cradle to have more movement suppression, re-mounted the DVR unit into a foam mount.... Lastly I am looking at Solid state drives ... We have a 4 channel DVR designed for Mobile use (dash-cam) We have (2) Garmin mini-golf ball cameras [one to rear of boat one to front of boat] then we have a chart plotter mapped into channel 3 and radar mapped to channel 4. ..... I am not readily by the dvr unit so I dont have exact unit info/ specs. any suggestions?

Buahaha ... CASH unfortunately "they" already have a vender list to order from... How Garmin cameras made that list i will never know!

Hello, I am Joel I have been in the entertainment side of life IE Lighting, Audio, Video sales, install and repair... Over the last 10 years the industry has moved into the digital age IE networking... Over the past 2 years we have found our company upgrading night clubs, bars, restaurants, hotels, etc Currently we provide CCTV solutions in California but recently have been certified to be a Federal contractor... I am excited to join such a resourceful and dynamic forum!

Its government so budget is not a problem, just a solution! they spec'd for a minimum of 350 gig HD so I am looking at Extreme duty SSD 340 Gig Hd msrp at 320.00 usd... I wish they would let me update the camera units from 200 TVL to 700tvl :/ I will post pics and specs once they confirm the invoice YAY for net45