TipoFloe

Amazing Stuff! Thanks for the info!

I don't know what an HDMI IR is or how it works... The remote control extenders work wonders for the remote controllers, but I don't know about IR extender for HDMI?? How far are the rooms?

While protecting your property, I think you're all set as long as you're not actively watching other people's property. I'm sure the original poster's neighbor will realize the benefit of the surveillance rather than being annoyed by it. Anyways, I agree with you that there is no clear law for it.

Just wondering what laws specifically guarantee your rights to monitor your property. Probably along the same lines as our second constitution lol.

Most DVRs use their MAC address as their DDNS address, plus a domain and a ".com" at the end or a variant. The whole thing should take less than 15 mins to set up if you know what you are doing, but since this is your first time, this is how you learn I guess. I can't help you with the error messages as they seem proprietary to the DVR... Have you tried contacting the manufacturer?

Hello, this is a classic case where regular Backlight Compensation (BLC) and its variants just do not suffice. If you must see in the areas where you have circled, you may need a camera with Wide Dynamic Range function. Be careful when you shop for it because there are many "fake" varieties of it. Stay away from any DWDR (Digital WDR) because it's jut as effective as BLC. Look for any WDR cameras that come with either a regular WDR or LWDR (low frame wide dynamic range) designation. To name a few image sensor and DSP solutions, PIXIM (Seawolf sensor and DSP) is the front runner in all WDR performance. Though you WILL find other cheaper products at a comparable feature. Look for keywords like Aurora 2 DSP or Spectra DSP. Sony also has a WDR variant in the Effio series, but you want to be careful when you select an Effio camera as they have 3 levels of performances, and the most common do not have WDR feature built in.

It's perfectly within your rights to monitor your property, even if some cameras may be pointing to your neighbor's house. Check to see if the problem camera has privacy masking function so that you can block out your neighbor's residence. If he sues you for invasion of privacy, all you need to do is take a snapshot of that camera and show the court that you are not invading his privacy rights.

Yeah, that connector is typically for cable TV and stuff. Often run on RG-6 cable. As Soundy suggest, if it really does go to a camera, you will need the converters, and a DVR to connect it to. But just 1 camera?

Get an IR illuminator.

Is there just one slot for the HDD connection? You should contact the manufacturer or the seller to obtain that information. Typically when a DVR has a format function, it shouldn't have a problem formatting any drives. But then again, a few manufacturers are adamant about using a specific HDD from a list that they provide. The compatibility and reliability have gotten better over the years, but this should give you a place to start.

I don't see why it should Are you talking about Chromatic Aberration? Why don't you post a pic? You may want to upgrade your camera to something with WDR in it to reduce the glares and "normalize" the picture...

596 is probably the vertical lines. Most camera specs list the horizontal lines before the vertical lines. Interesting image sensor you have there, 1020 x 596? Who makes it? Here's a more detailed key difference between NTSC vs. PAL http://en.wikipedia.org/wiki/PAL#PAL_vs._NTSC And also, typically, PAL standard always had higher TV lines in exchange for the useless 5 FPS that NTSC uses. Here's a comparison chart: http://www.diffen.com/difference/NTSC_vs_PAL

I guess seeing is believing. These two pictures were taken from the same DVR, one showing through BNC and the other showing through HDMI. Up until around 2006, most DVRs used a multiplexer chip and a video output that only could put out 420TVL maximum. However, the introduction of VGA, DVR and consequently HDMI increased the DVR output to 2 megapixel. You're right about the fact that what difference does it make with analog cameras, but consider the following: You are looking at an image that's at most 500TVL vs. You are looking at an image that's 1080 TVL with upscaled imaged, meaning, your LIVE display will be sharp as heck!

You're almost there. Your bridge is working fine. Connect the DVR to the bridge using the same network cable. Ports - leave the media port and web port alone. You can actually change them in case your VIRGIN router uses port 80 (and probably does). You may want to change the web port to 8000 or 8080. IP Address (unique number like your house number)- Enter a unique IP address like the one in the computer, but the last three numbers will have to be different. Subnet Mask (groups of IP addresses, or classes)- Enter the same subnet mask as your computer Gateway (how your DVR will transmit or access the internet) - enter the same gateway as your computer DNS (it's like the post office) you can enter 4.2.2.1 (or the one provided by your ISP - can be found on your laptop as well by typing ipconfig/all)- it keeps track of all the domain names associated with actual IP addresses. uPnP (universal plug and play) - IF THIS FUNCTION WORKS, THEN YOU DON'T HAVE TO WORRY ABOUT PORT FORWARDING There is one last piece of information that's missing - DDNS host name. Your DVR should have come with a unique DDNS host name, or a way to register so that it's also unique... Note that if you're using a web browser for connection to your dvr, you will have to use port 8080 if you've changed the web port above to 8080. For internal IP address (let's say that the DVR IP address is 192.168.1.99), you can simply type in http://192.168.1.99:8080 and it will open up your web browser interface. From the outside of your network (outside of your home) you will either have to type in the public IP (whatismyip.com) plus :8080 at the end. Don't forget the http:// in front. However, since MOST internet services offer dynamic IP, this will probably not work for you after a few days (even hours). This is where the DDNS comes in. So let's say that your DVR has the DDNS name of yourdvr.dvr.com then you'd type in http://yourdvr.dvr.com:8080 to connect to your DVR. Good luck!

Hi, The wifi bridge is the same as this one: http://www.amazon.co.uk/Vonets-VAP11G-WIFI-Bridge/dp/B0050AI804 Unfortunately the 'instructions' it came with was next to useless... I just followed the installer / set-up CD until it said 'congratulations... it's ready to use'. I plugged it into my dvr (the wifi bridge flashes blue... supposedly this means it is picking up my wifi signal) and went into the menu area of the dvr (to set up the network for the ip cameras) but haven't a clue what to put. I'm guessing the bridge device is working correctly but I have no idea about the IP side of things? Thanks, Sam Turn off your wifi on your laptop, connect the laptop via CAT5e network cable to the bridge and see what IP address it assigns you. If you followed step 1 properly, you should have 3 sets of numbers - IP address, subnet and gateway. After you connect the laptop to the bridge, see if you can obtain the same information from the command prompt first and write it down here.

Hello, I was just providing basic universal networking setup procedure. If you have set up your bridge already and you know it's working, then it's just matter of assigning the right IP address, subnet and gateway for your DVR. One way of verifying your bridge connection is to turn off WIFI on your laptop, connect via a network cable to the bridge and see if you can ping the rest of your devices (try pinging your VIRGIN router). I do not know if your bridge has such modes, but I'd figured it'd come with all the choices...?

Hey, according to the spec for your camera http://www.bhphotovideo.com/c/product/594288-REG/ARM_Electronics_OCD36XSDWD_OCD36XSDWD_36x_Optical_Zoom.html, the lens module is from 3.4mm to 122.4mm which does make it a 36x optical zoom PTZ camera. It may be that the camera is not displaying what zoom ratio it's using...? I don't understand your second paragraph. What are you trying to do?

Networking can be daunting at first, but if you understand the concept of it, it should be easy as slicing bread! 1. On your Virgin Media Wifi connection, where your laptop, ipad and etc are connected. 1-1. On your laptop. go to START, RUN. It should open a small window. Type in CMD (windows XP and up) and it will open up the command prompt (black window). 1-2. Type ipconfig in the command prompt, you should get a series of information, such as IP address, subnet mask and gateway - write them down. 1-3. IP address is a unique IP address assigned to your laptop. Subnet is just a division address types and gateway is the IP address of your Vifgin Media Wifi connection. 2. On your VONETS VAP11G wifi bridge. 2-1. Connect your laptop to the bridge via a network patch cable, and then access the IP address of the bridge. 2-2. See if your VONETS picks up your VIRGIN wifi signal. 2-3. set it to STATIC mode (the IP address never changes), and then assign an IP address that does not overlap with the rest of the products. If your laptop has 192.168.1.101, and so forth, you may want to assign the bridge 192.168.1.200. Subnet should be the same as on your laptop, and the gateway should be the same as your laptop as well. 2-4. On your laptops command prompt, PING one of the other devices that are already on the network (which can be often found within the router itself). If your iPad has an IP address of 192.168.1.102 for example, PING 192.168.1.102 and you should get 4 returns. 3. On your DVR or IP camera. 3-1. Go to the network setting of the DVR or the IP camera, set it to STATIC mode and then assign a unique IP address. Subnet and gateway should match the one on your laptop. 3-2. Get your laptop on your VIRGIN WIFI again, and then PING the IP address of the DVR or the IP camera. If you get returns, then you have a successful bridged connection. 4. Back to your Virgin Router 4-1. Go to the port forwarding section, and then open the appropriate ports for the DVR or the IP address. You should not have a problem accessing your device within your wireless LAN (using internal IP address as shown on your device) and from WAN (outside of your location) by accessing the PUBLIC IP address of your router - it can be easily found using http://www.whatismyipaddress.com. Or if your DVR or IP camera offers a DDNS service, then you can use that information to connect as well. Good luck!

Hello, you are looking at a PTZ camera one of the forum members are selling. I'm sure he will have much more detailed information. I'm not going to comment on the camera since I don't want to interfere with the sales. But the wiring is quite simple. If you have a keyboard controller, then it should have a TX+ and TX-, whereas the RX+ and RX- should be present on the camera. You can use a CAT5e or 18/2 cable to connect and transmit the commands. If you're going to connect the controller to the DVR and then to the PTZ, you may first want to verify that your controller is capable of controlling your DVR as well. You may want to PM TOMCCTV for further details.

You will notice a HUGE difference between the BNC output vs. HDMI output. Everything's going to be sharper! Go for the HDMI!

The eyeball camera housing is just a generic that any camera manufacturer uses. If you already have the camera, contact the manufacturer and ask them if they can put the HD module into the camera for you.

The biggest advantage of progressive scan is that the captured pixels are actual rather than two interlaced together, hence resulting in a blur-free moving images. Of course, this can be affected by the video compression mode, but the point here is that progressive scan will provide the actual TV lines it claims to offer. Think of this like the upscaling (interlaced) of DVD players to 720p or 1080p whereas Blue-ray (Progressive) players output true 720p or 1080p. My reference may not be 100% accurate, but I hope you get the point...?

I was hoping to spot a reset or a set of jumpers, but can't find anything. Let's try this. Try removing the battery that probably keeps the date up to date. If that clears the memory and resets everything, so should the password, and you can try again the sequences... Good luck...

Don't forget to deduct 25% from all of your available Ah as the DC to AC power converter will lose that much power during the conversion. Unless you can wire everything directly to the battery, but I don't recommend that.

1. Contact your network administrator 2. Contact AV tech and obtain port forwarding information. 3. Contact your ISP to properly setup port forwarding for your DVR. Or, 4. Contact your router manufacturer to set up port forwarding for your DVR.