ryn0909

lol thats the only thing ive found for my unit. i found that about a week ago. i contacted tech support but they dont respond

thats another thing i have not been able to locate.... i have been searching for months

I mean the picture on the monitor when the recorder is loaded and requests authorization. Find firmware for you dvr! ohh.... you are talking about the GUI main menu?? ill post one in a few minutes

i wonder if there are any other possible login names to use other than root..... most importantly, i wonder who knows or where to find out the default root password..

there is no menu for console login. it looks just like the picture posted above, all it says is NFDVR Login:

the thing is, i dont know the defaut password for console login. ive looked all over the internet and cant find very much info about console login, hot keys, or debugging. it seems like its a very secretive topic. people dont talk much about it.

Make screenshot of this!

Maybe need press some button on the panel? i did, with unit powered off, if i press and hold setup, display, 2 and power unit on, it will eventually halt the boot process and bring me to a login prompt that says "NFDVR Login" i know the username is "root" but i cant figure out the password

DM646x initialization passed! TI UBL Version: 1.50 Booting Catalog Boot Loader BootMode = NAND Starting NAND Copy... Valid magicnum, 0xA1ACED66, found in block 0x00000006. DONE Jumping to entry point at 0x81080000. U-Boot-1.2.0 (Mar 25 2010 - 18:51:36) I2C: ready DRAM: 256 MB unknown vendor=0 Flash: 0 kB NAND: Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 256 MiB In: serial Out: serial Err: serial ARM Clock :- 493MHz DDR Clock :- 408MHz [ANF1648 Initialize] [sPI INIT] System Reset Check..was passed [signal Type is [NTSC]] [ANF1648 Spot Init] [Pannel Type is ITX-5 ] [RC Type is AVR4816-ITX ] [Mac address [00:11:5F:06:80:61 ]] [before Shutdown => abnormal shutdown] Hot Key MAGIC_KEY_PASSWD_RESET [Tw286x Initialize / Signal Type : NTSC] [TW2865 dev[0x28] done] [TW2865 dev[0x29] done] [TW2865 dev[0x2a] done] [TW2865 dev[0x2b] done] [Fan On] [FB ADDR [0x8e000000]] Reading data from 0x7ff800 -- 100% complete. [MDIN240 Initialize] DM646x initialization passed! TI UBL Version: 1.50 Booting Catalog Boot Loader BootMode = NAND Starting NAND Copy... Valid magicnum, 0xA1ACED66, found in block 0x00000006. DONE Jumping to entry point at 0x81080000. U-Boot-1.2.0 (Mar 25 2010 - 18:51:36) I2C: ready DRAM: 256 MB unknown vendor=0 Flash: 0 kB NAND: Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 256 MiB In: serial Out: serial Err: serial ARM Clock :- 493MHz DDR Clock :- 408MHz [ANF1648 Initialize] [sPI INIT] System Reset Check..was passed [signal Type is [NTSC]] [ANF1648 Spot Init] [Pannel Type is ITX-5 ] [RC Type is AVR4816-ITX ] [Mac address [00:11:5F:06:80:61 ]] [before Shutdown => abnormal shutdown] Hot Key MAGIC_KEY_PASSWD_RESET [Tw286x Initialize / Signal Type : NTSC] [TW2865 dev[0x28] done] [TW2865 dev[0x29] done] [TW2865 dev[0x2a] done] [TW2865 dev[0x2b] done] [Fan On] [FB ADDR [0x8e000000]] Reading data from 0x7ff800 -- 100% complete. [MDIN240 Initialize] [** Warning ** HDMI/DVI DDC Edid CheckSum Error!!!] [** Warning ** Analog DDC Edid CheckSum Error!!!] [Video Output Infomation : Unknown Video Size Set Default 1024x768p60] [MDIN240 HDMI INIT] [set Output Video Clocks 27MHz] [Turn_On_DSP] [uART2 INIT] [uART1 INIT] Hit any key to stop autoboot: 0 Current Seq [10001] [10000] ====================================================================== model [ANF1648 ] vendor [100 ] lang [English ] option [ ] version [14310.1.38.100 ] ====================================================================== ******** Boot mode is Ping ******** ** WARNING ** Invalid Update Magic!!! Cannot write updata variable at 0x8100000 Loading from NAND 256MiB 3,3V 8-bit, offset 0x800000 Reading data from 0x800000 -- 100% complete. Image Name: Linux-2.6.10_mvl401-davinci_evm- Created: 2010-03-02 6:40:11 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1728840 Bytes = 1.6 MB Load Address: 80008000 Entry Point: 80008000 Reading data from 0x9a6000 -- 100% complete. ## Booting image at 80200000 ... Image Name: Linux-2.6.10_mvl401-davinci_evm- Created: 2010-03-02 6:40:11 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1728840 Bytes = 1.6 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK OK No initrd Starting kernel ... elapsed_time_msec [42922] NF_profiling Stop 42 Sec, 922 MSec [use Nand Copy Module] Valid ID Not Found maf_id[0x00] dev_id[0x00] Uncompressing Linux.................................................................................................................... done, booting the kernel. Linux version 2.6.10_mvl401-davinci_evm-PSP_01_30_00_082 (pakkhman@nf.intellix.co.kr) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.135.0702900 2007-04-01)) #108 Tue Mar 2 15:40:06 KST 2010 CPU: ARM926EJ-Sid(wb) [41069265] revision 5 (ARMv5TEJ) CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets Machine: DaVinci DM6467 EVM Ignoring unrecognised tag 0x54410008 Memory policy: ECC disabled, Data cache writeback DM6467 Built 1 zonelists Kernel command line: console=ttyS0,115200n8 noinitrd rw ip=::::NFDVR:eth0:off root=/dev/mtdblock9 rootfstype=yaffs2 mem=120M eth=00:11:5F:06:80:61 passwd_reset num_ch=16 signal_type=ntsc model_type=ANF_1648 crc_ubl=99c953dd crc_ker=ab3ddeba crc_fpga=15a5290d pannel_type=ITX-5 rc_type=AVR4816-ITX hw_ver=MAFS116C TI DaVinci EMAC: Kernel Boot params Eth address: 00:11:5F:06:80:61 PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 120MB = 120MB total Memory: 117888KB available (2874K code, 691K data, 160K init) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok change_boot_logo called spawn_desched_task(00000000) desched cpu_callback 3/00000000 ksoftirqd started up. desched cpu_callback 2/00000000 desched thread 0 started up. NET: Registered protocol family 16 DaVinci: 48 gpio irqs Registering platform device 'serial8250.0'. Parent at platform Registering platform device 'musb_hdrc'. Parent at platform Registering platform device 'nand_davinci.0'. Parent at platform [arch_dma_init:2693]: DMA CC REG BASE ADDR=e1000000 [arch_dma_init:2759]: DMA TC[0] REG BASE ADDR=e1010000 [arch_dma_init:2759]: DMA TC[1] REG BASE ADDR=e1010400 [arch_dma_init:2759]: DMA TC[2] REG BASE ADDR=e1010800 [arch_dma_init:2759]: DMA TC[3] REG BASE ADDR=e1010c00 [arch_dma_init:2815]: Shadow REG BASE ADDR = e1002000 DaVinci I2C DEBUG: 15:37:46 Mar 2 2010 DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected [i2c_davinci_reset] @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ Registering platform device 'i2c'. Parent at platform SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub musb_hdrc: version 2.2a/db-0.4.8 [cppi-dma] [host] [debug=0] usb_hid_thread set priority failed usb_hid_thread set priority SCHED_FIFO pri[100] musb_hdrc: ConfigData=0x06 (UTMI-8, dyn FIFOs, SoftConn) musb_hdrc: MHDRC RTL version 1.500 musb_hdrc: USB Host mode controller at c8000000 using DMA, IRQ 13 musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. yaffs Mar 2 2010 15:37:17 Installing. watchdog: TI DaVinci Watchdog Timer: timer margin 64 sec DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected DaVinci I2C WARNING: i2c: NACK detected [Ds1339 RTC] DaVinci I2C WARNING: i2c: NACK detected Registering platform device 'DavinciHD_vdce.2'. Parent at platform Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 2 ports, IRQ sharing disabled Registering platform device 'serial8250'. Parent at platform ttyS0 at MMIO 0x1c20000 (irq = 40) is a ST16654 io scheduler noop registered io scheduler anticipatory registered loop: loaded (max 8 devices) pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com Registering platform device 'ti_davinci_emac'. Parent at platform TI DaVinci EMAC: MAC address is 00:11:5F:06:80:61 TI DaVinci EMAC Linux version updated 5.0 TI DaVinci EMAC: Installed 1 instances. PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered Universal TUN/TAP device driver 1.5 ©1999-2002 Maxim Krasnyansky netconsole: not configured, aborting i2c /dev entries driver Linux video capture interface: v1.00 SPI DRIVER INITIALIZE.. fs1648 driver loading g_ntsc_pal[0] FPGA reset...OK. Register chrdev OK Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx MUX: initialized ATAEN usb 1-1: new high speed USB device using musb_hdrc and address 2 usb 1-1: Product: USB2.0 Hub hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected hda: ST3500418AS, ATA DISK drive hub_port_connect_change USBHID_EMI #2 name[hub] usb 1-1.2: new high speed USB device using musb_hdrc and address 3 usb 1-1.2: Product: USB Storage usb 1-1.2: SerialNumber: 000000000033 usb 1-1.4: new full speed USB device using musb_hdrc and address 4 usb 1-1.4: Product: 2.4G Keyboard Mouse usb 1-1.4: Manufacturer: MOSART Semi. hdb: WDC WD2500JS-60NCB1, ATA DISK drive elevator: using anticipatory as default io scheduler ide0 at 0xe10661f0-0xe10661f7,0xe10663f6 on irq 22 hda: max request size: 1024KiB hda: 976773168 sectors (500107 MB) w/16384KiB Cache, CHS=60801/255/63 /dev/ide/host0/bus0/target0/lun0: p1 p2 hdb: max request size: 1024KiB hdb: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63 /dev/ide/host0/bus0/target1/lun0: p1 p2 ide0: BM-DMA at 0xe1066000-0xe1066007, BIOS settings: hda:pio, hdb:pio ---- IDE_PALM_CLK ---- 00000008 ---- ATA Timing ---- 2, b, 3 ---- IDE_PALM_CLK ---- 00000008 ---- ATA Timing ---- 2, b, 3 ide1: BM-DMA at 0xc8060000-0xc8060007, BIOS settings: hdc:DMA, hdd:DMA nand_davinci nand_davinci.0: Using soft ECC NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bit) Creating MTD partitions on "nand_davinci.0": nand_davinci nand_davinci.0: hardware revision: 2.2 usbcore: registered new driver cdc_acm drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. input: USB HID v1.10 Keyboard [MOSART Semi. 2.4G Keyboard Mouse] on usb-musb_hdrc-1.4 input: USB HID v1.10 Mouse [MOSART Semi. 2.4G Keyboard Mouse] on usb-musb_hdrc-1.4 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice Registering Audio Devices. Total communication peripherals (ASP) : 2 [register_sound_dsp] [register_all_codecs][0] minor = 3, mixer_dev_id = 0 [audio_aic32_write] address = 0x00, val = 0x0000 [audio_aic32_write] address = 0x2a, val = 0x006c [audio_aic32_write] address = 0x33, val = 0x0099 [audio_aic32_write] address = 0x41, val = 0x0099 [audio_aic32_write] address = 0x56, val = 0x0099 [audio_aic32_write] address = 0x5d, val = 0x0099 [audio_aic32_write] address = 0x25, val = 0x00e0 [audio_aic32_write] address = 0x26, val = 0x0010 [audio_aic32_write] address = 0x08, val = 0x00c0 [audio_aic32_write] address = 0x09, val = 0x0040 [audio_aic32_write] address = 0x0f, val = 0x0017 [audio_aic32_write] address = 0x10, val = 0x0017 [audio_aic32_write] address = 0x2f, val = 0x00a4 [audio_aic32_write] address = 0x40, val = 0x00a4 [audio_aic32_write] address = 0x52, val = 0x00a4 [audio_aic32_write] address = 0x5c, val = 0x00a4 [audio_aic32_write] address = 0x13, val = 0x0004 [audio_aic32_write] address = 0x16, val = 0x0004 [audio_aic32_write] address = 0x11, val = 0x00ff [audio_aic32_write] address = 0x12, val = 0x00ff [audio_aic32_write] address = 0x1a, val = 0x0080 [audio_aic32_write] address = 0x1b, val = 0x002e [audio_aic32_write] address = 0x1c, val = 0x0000 [audio_aic32_write] address = 0x1d, val = 0x0080 [audio_aic32_write] address = 0x1e, val = 0x002e [audio_aic32_write] address = 0x1f, val = 0x0000 [audio_aic32_write] address = 0x2b, val = 0x0008 [audio_aic32_write] address = 0x2c, val = 0x0008 [audio_aic32_write] address = 0x19, val = 0x0040 [audio_aic32_write] address = 0x07, val = 0x000a [audio_aic32_write] address = 0x02, val = 0x0000 [audio_aic32_write] address = 0x03, val = 0x0092 [audio_aic32_write] address = 0x04, val = 0x001c [audio_aic32_write] address = 0x05, val = 0x002c [audio_aic32_write] address = 0x06, val = 0x0001 [mcasp_configure] CODEC_IS_MASTER Codec with ID = 0 on ASP = 0 is initialized.Using minor number : 3 [register_sound_dsp] [audio_aic32_write] address = 0x00, val = 0x0000 [audio_aic32_write] address = 0x2a, val = 0x006c [audio_aic32_write] address = 0x33, val = 0x0099 [audio_aic32_write] address = 0x41, val = 0x0099 [audio_aic32_write] address = 0x56, val = 0x0099 [audio_aic32_write] address = 0x5d, val = 0x0099 [audio_aic32_write] address = 0x25, val = 0x00e0 [audio_aic32_write] address = 0x26, val = 0x0010 [audio_aic32_write] address = 0x08, val = 0x00c0 [audio_aic32_write] address = 0x09, val = 0x0040 [audio_aic32_write] address = 0x0f, val = 0x0017 [audio_aic32_write] address = 0x10, val = 0x0017 [audio_aic32_write] address = 0x2f, val = 0x00a4 [audio_aic32_write] address = 0x40, val = 0x00a4 [audio_aic32_write] address = 0x52, val = 0x00a4 [audio_aic32_write] address = 0x5c, val = 0x00a4 [audio_aic32_write] address = 0x13, val = 0x0004 [audio_aic32_write] address = 0x16, val = 0x0004 [audio_aic32_write] address = 0x11, val = 0x00ff [audio_aic32_write] address = 0x12, val = 0x00ff [audio_aic32_write] address = 0x1a, val = 0x0080 [audio_aic32_write] address = 0x1b, val = 0x002e [audio_aic32_write] address = 0x1c, val = 0x0000 [audio_aic32_write] address = 0x1d, val = 0x0080 [audio_aic32_write] address = 0x1e, val = 0x002e [audio_aic32_write] address = 0x1f, val = 0x0000 [audio_aic32_write] address = 0x2b, val = 0x0008 [audio_aic32_write] address = 0x2c, val = 0x0008 [audio_aic32_write] address = 0x19, val = 0x0040 [audio_aic32_write] address = 0x07, val = 0x000a [audio_aic32_write] address = 0x02, val = 0x0000 [audio_aic32_write] address = 0x03, val = 0x0092 [audio_aic32_write] address = 0x04, val = 0x001c [audio_aic32_write] address = 0x05, val = 0x002c [audio_aic32_write] address = 0x06, val = 0x0001 [mcasp_configure] CODEC_IS_MASTER SPDIF on ASP = 1 isinitialized.Using minor number : 19 NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 8192 bind 16384) NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 ADDRCONF(NETDEV_UP): eth0: link is not ready IP-Config: Incomplete network configuration information. yaffs: dev is 32505865 name is "mtdblock9" yaffs: Attempting MTD mount on 31.9, "mtdblock9" Vendor: TSSTcorp Model: CDDVDW SH-S223L Rev: SB02 Type: CD-ROM ANSI SCSI revision: 00 sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5 VFS: Mounted root (yaffs2 filesystem). Mounted devfs on /dev Freeing init memory: 160K INIT: version 2.85 booting Valid magicnum, 0xA1ACED66, found in block 0x00000006. DONE Jumping to entry point at 0x81080000. U-Boot-1.2.0 (Mar 25 2010 - 18:51:36) I2C: ready DRAM: 256 MB unknown vendor=0 Flash: 0 kB NAND: Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 256 MiB In: serial Out: serial Err: serial ARM Clock :- 493MHz DDR Clock :- 408MHz [ANF1648 Initialize] [sPI INIT] System Reset Check..was passed [signal Type is [NTSC]] [ANF1648 Spot Init] [Pannel Type is ITX-5 ] [RC Type is AVR4816-ITX ] [Mac address [00:11:5F:06:80:61 ]] [before Shutdown => abnormal shutdown] Hot Key MAGIC_KEY_PASSWD_RESET [Tw286x Initialize / Signal Type : NTSC] [TW2865 dev[0x28] done] [TW2865 dev[0x29] done] [TW2865 dev[0x2a] done] [TW2865 dev[0x2b] done] [Fan On] [FB ADDR [0x8e000000]] Reading data from 0x7ff800 -- 100% complete. [MDIN240 Initialize] 0 Mounting a tmpfs over /dev...done. DM646x initialization passed! Creating initial device nodes...TI UBL Version: 1.50 Booting Catalog Boot Loader BootMode = NAND Starting NAND Copy... Valid magicnum, 0xA1ACED66, found in block 0x00000006. DONE Jumping to entry point at 0x81080000. U-Boot-1.2.0 (Mar 25 2010 - 18:51:36) I2C: ready DRAM: 256 MB unknown vendor=0 Flash: 0 kB NAND: Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 256 MiB In: serial Out: serial Err: serial ARM Clock :- 493MHz DDR Clock :- 408MHz [ANF1648 Initialize] [sPI INIT] System Reset Check..was passed [signal Type is [NTSC]] [ANF1648 Spot Init] [Pannel Type is ITX-5 ] [RC Type is AVR4816-ITX ] [Mac address [00:11:5F:06:80:61 ]] [before Shutdown => abnormal shutdown] Hot Key MAGIC_KEY_PASSWD_RESET [Tw286x Initialize / Signal Type : NTSC] [TW2865 dev[0x28] done] [TW2865 dev[0x29] done] [TW2865 dev[0x2a] done] [TW2865 dev[0x2b] done] [Fan On] [FB ADDR [0x8e000000]] Reading data from 0x7ff800 -- 100% complete. [MDIN240 Initialize] done. 0 Mounting local filesystems: mount none on /var/run type tmpfs (rw) none on /tmp type tmpfs (rw) Setting up networking (ifupdown) .. Cleaning: /etc/network/run/ifstate done. Starting network interfaces: ifup: Ignoring unknown interface eth0 failed (1: ). Starting hotplug subsystem:

ill post them when i get home from work

* Restart Web Server... ! /NFDVR/webra/lighttpd/sbin/lighttpd.sh: can't stop httpd netsvr-Message: my_getaddrinfo : hints [0][2][1][6] [222.122.199.211](16) socket make ok ddns2_connect : errno == EINPROGRESS or EALREADY. errno[115] Operation now in progress connect_test: connect fail... sleep 2 SEC~~!!! + httpd is started [ ok ] ./proxy_svr child 1248 terminated ./proxy_svr child 1247 terminated proxy_ret tag[0]ret[0] nf_main-Message: ---------------------------------------- nf_main-Message: NF_HOST VER [0.1.0] nf_main-Message: NF_HOST SYSID [LINCOLN] nf_main-Message: NF_HOST SWVER [14310.1.38.100] nf_main-Message: ---------------------------------------- nf_main-Message: nf_sysman_hotkey_is_passwd_reset on!! Welcome to jbshell! jbsh:> ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ MontaVista® Linux® Professional Edition 4.0.1 (0601652) NFDVR login: nf_main-Message: INIT_GUI !!!!!![FS1648] set live maks color. y:0x0040/uv:0x00c7. !!!!!!!!!!!!!!!!!!!!!!!2 nf_mainFS1648_CHG_MASK, -Message: init_gui done!

so i have this standalone dvr system (isis avr1612) running MontaVista® Linux® Professional Edition 4.0.1 (0601652) and im connected to the serial port (rs232) and connected using PuTTY. somehow i finally got it to stop booting and its sitting at a login prompt that says..... > NFDVR login: and this is where im stuck... ive tried admin:admin admin:1234 admin:12345 root:admin and im sure i could guess till im blue in the face, but id rather not. would anyone happen to know the default login:pass for this unit???

Almost forgot...... the default ADMIN password is 1234

hi i just recently purchased this dvr system from a guy on craigslist and upon turning it on, i found it to be asking for the password of the ADMIN account. the guy i bought it from doesnt know it. is there a way to reset the password or any kind of workaround to it??? also it says the make is an "Isis" however it doesnt say the model name anywheredoes anyone know whaty model this is??

OK so i found out the soultion, if anyone cares...... Isis model: AVR-1612 To reset the unit back to factory defaults there is a key sequence to follow..... Unplug the power cord from the back of the unit. With the power cord UNPLUGGED, you are going to PRESS and HOLD the (DISPLAY), (SETUP) and the (1) buttons, at the same time. Continue holding the 3 buttons and plug the power cord back into the unit. Continue holding the buttons in for about 10 seconds while the unit is powering up. release the buttons and wait for the unit to detect the disks installed and to boot up. you may have to wait longer than normal for the unit to boot up, but be patient, it will boot up. hope this helps someone out there.

UPDATE: This is a model AVR-1612 made by Isis. still looking for a way to get around the ADMIN password

hi im new to this forum and look forward to learning some cool stuff