t310483317

2018-06-24 11:47:43 DS-7208HVI-SV0820140823AAWR477513631WCVU Verification Code VZIUQL Hope someone can help

Cheers Daryl but no game, so put vid + to the centre wire of the bnc cable And I put scr to the outer mesh wire of bnc cable nothing so tried wiring scr to scr - to terminate it or something I read? and that didn't bring it up either Not sure what else to try but any suggestions from anyone welcome!

Thank you so much for the reply! I'll give this a go soon and report back Cheers!

Awesome glad to be of help

An alternative I came up with was £30 3G Router £10 3G Dongle - connected the two and ethernet DVR to 3G Router - and boom live viewing available and emails with snapshot motion detection. DVR + 8 cameras @ £200 Or one 3G/4G IP sim card camera @ £250 was the cheapest I found.

for a samsung SRN-472S factory reset try the following from the remote: FREEZE ALARM FREEZE ALARM FREEZE RETURN Else does this resemble your DVR? The reset button is to the right of the console port and to the left of the Network 4 port. Hold it in for 10 seconds and release, it will reset everything to default, however you will lose everything you had on it and won't be able to recover it. Hope this helps a little.

What system are you using most or what system are you looking for a stable application for?

In the systems I have setup if you connect remotely or locally using a browser then 80/8080 will work fine and it connects but for some awkward reason using an application on a Windows system .exe file or Android application/iOS then the mobile application uses a different port in my cases they have varied - 3892, 34567, 18002, 18004, 1842, 9000 So try and have a look in the network settings and see if it mentions any other ports at all media port, web port, second stream port etc Hope this helps a little. Also I have not found a solution for some older DVR machines to play web based streams/video playback in browser, I can login usually and set settings but when viewing live it won't load a activex error etc occurs, so the solution for me was to run Internet Explorer in Compatibility View and as administrator then the DVR pushes a download if the settings are set properly (insecurely)

I do believe depending on what firmware you have running when you have continuous recording enabled, and set motion detection - when on the playback screen it should show you obviously that there is footage available but also when the event/motion/alarm occurred in a different colour. If you've setup alarm/motion detection and it isn't highlighting this on the playback screen then chances are you don't have that option - are you using the dvr/monitor and mouse or are you trying to view through web based or application software?

I have all of my cameras on lowest and I have tried to define the areas and risk free as possible to avoid random detections but if it rains badly etc then I can get 200+ false detection emails through the night which wastes data- if you come across any solutions then post up

I take it when you say you have forgotten it then you changed it from default? If not some standard ones you could try if it was still default: 000000 123456 admin NULL 12888 1234 12345 no password just enter username and click login? If none of these work it might be worth powering off the DVR and unplugging it then opening the cover, removing any small watch battery(s) you can see - plug it back in and start the system up for about one minute, then again shut it down and unplug and add the battery(s) back in. And if that doesn't work then depending on your DVR you could try networking and using telnet to access into it remotely.

000000 123456 admin NULL 12888 1234 12345 no password just enter username and click login? If none of these work it might be worth powering off the DVR and unplugging it then opening the cover, removing any small watch battery(s) you can see - plug it back in and start the system up for about one minute, then again shut it down and unplug and add the battery(s) back in.

Hi can anyone help me with what wires should go where? I've hooked up 24v but still got these connections above to hook up but not sure where to start? DATA+ DATA- SCR VID(+) SCR (-) Is a document I found online but again still not understanding it unfortunately. Image of the unit itself. Any replies much appreciated!

How are you powering it?

Have you defined the zones for the motion to be detected within? Silly question probably..