prsvarma

I was trying to connect Hikvision DVR on net for view on Mobile. The router Dlink 600m is hooked ton ADSL modem. The internet is working perfectly fine. To configure: I gave a static IP to dvr [192.168.0.10] and was trying to port forward. the external IP address [Wan] is 152.xxx.xxx.xxx. but in the DVR am seeing a different external address 172.XXX.XXX.XXX with a different gateway 49.xx.xx.xx. when i type 172.xxx.xxx.xxx in the address bar am taken back to the DVR interface screen. i am not sure how this 172 ipaddress ie being displayed for DVR. am not able to Port forward because of this. Please help to know me the possible reasons To add on: i did further investigation. the internetip [checked through whatsmyip] shows 152.xx and the router wan ip is 172.xx[this is what dvr is picking]. i had called the ISP and they have assured me on opening the required ports. but would this solve the problem? or is it that i have to request them to have a single ip as the router wan ip

I need help on the problem which i am facing on installation of 6 hikvision cameras using cat 5 STP Details: 5 Bullet cameras - 12 V DC of which one has 40 m IR other have 20 m 1 Dome - 12 V IR 20 m All are HD The cameras are outdoor ones are far apart from DVR. the 40 m IR bullet camera is 110 m from DVR. others are 60, 50, 60 m etc. one bullet and dome is in the office premises itself close to the DVR. I have used passive video balus for all Cat 5 STP is used for video and power. Total 3 cables were used for 6 cameras [2 pairs for two bullets in single line, one pair for power]. i used 12 v 20 amp power supply for powering the ameras The problems i am facing are: 1. Day time i get 3 cameras images clearly. hooking the fourth results in blurred images/distortions in a few cameras. images comes and goes in a few cameras. i initially used 12 v and 10 amps & 12 v and 5 amps powersupply but of no use. 2. i got a 12v 20 amps but with little difference. The problem inceases at night when IR goes on. the camera at 110 [40 m ir] went down and doesn't work even when hooked to 12 v 20 amp PS alone. Other cameras shows more distorted image I guess its because of a voltage drop but wonders why even it doesn't work with a 20 amp PS. There are no power sources available to most of the bullet cameras 3. Cameras [2 nos] in the office complex [10 m from DVR} works but has a colour band moving continuously in the screen one moving from right to left and other has moving colour band from left to right. is it because of any signal leaking? Please help me to resolve the issue. please give your valuable suggestions

Hi I have a query. i am using this item for the first time. The requirement is to connect two monitors to CCTV DVR. one monitor is around 50 m away from dvr. [other is just adjacent]. i used a vga splitter with one connecting to the monitor near and other to the extender via a male vga cable. 1. immediately when i connect to the extender the images on the first monitor gets blurred. 2. while connection RG45 with cat5 STP over this the images gets grained 3. No image comes in the monitor 50 m away and monitor switches off Please help to resolve this issue prs

I am facing a problem with my 8 channel HD DVR. There was frequent issues with the camera connected to channel 1 not showing any image, but later it got rectified automatically. Today morning the CCTV camera connected to this channel stopped working. i doubt the camera has got damaged as it is not working directly to any channels. other cameras when connected to CH1 is not showing images but works fine when connected to other channels. Any vies and help on this? Is my DVR damaged or some issue with setting?