cctvlad

Hi there I have a pair of IPC-2100 ip cameras on an wds network (engenious access points)when I add the second camera the ping rises to a maximum of 400ms thus network is slowing down at the NVR end. My noise floor is -48 to -60dbm maximum. what would be causing this as i need the ping to be relatively low to achieve proper frame rates. any chance of help?

Hi all for the the life of me what would cause one of bullet type IR cameras with a built in OSD to behave erratically and stay on. if i switch it off its reverted back to default and it comes on within the hr again. IR camera has a pigtail with osd buttons attached to it? to be fair the osd button stay outside the connection enclosure box would moisture cause this?

Hope that works for the DVR im getting !! thanks tomcctv

what is alarm triggering screen tips I'm looking a nvr that would trigger motion to full screen on the monitor e.g. someone walks through the door then live image goes full screen any ideas lads?

might buy from ADATA don't know yet depends on the full screen triggers. avermedia NVR/DVRs have them. RFconcepts supply avermedia...bit pricey though. what is alarm triggering screen tips?

HI all got a gig to do at a fuel yard decided to go IP as picture quality is mucho improved! Im looking for a dahua nvr 16 ch however I want a motion trigger that will put a specific camera to go full screen (eg. a car coming through the gate or someone coming in the door) can dahua nvr do this? I know that avermedia recorders can do this though. and is alibaba worth buying from? cctv lad hope yous are all well

Hi all need some help on a job , Don't usually go for wireless kits for cctv I've had to because of the distance from the house to the farm yard. ok. I've purchased two 50mw 2.4ghz transmitter and receivers. one is 20 ft away and the other is 423 ft away the receiver box is custom made with antennas outside of it and they are like 10 inches apart. the garage camera (20ft) is at channel 1 and works perfectly. the shed camera (423ft) is at channel 3 and picture just comes as noise and sees channel 1 momentarily and goes away. however if i put it at channel 1 the picture gets stronger with them both in conflict and I see the shed its almost clear but its a picture thats in pulling at each other. why can i not get a stable picture at channel 2,3 or 4? is the transmitter out of range or is the receivers too close to each other?

its 2 am here in N.Ireland but ill get some to you. might try video via digital camera. what im finding hard at the mo is bringing out good night vision and how to reduce noise.(think its unavoidable and i think non IR cameras with IR floods would be more capable? I just bought a effio-e 700 tvl its like 160 dollars in your currency 72 leds BLC and all that. but it claims to have 60 metre range but it is pointed towards an open yard. just would like better low light exposure. whats ur take on IR cameras?

hey soundy its like ghosting but its not the channels themselves. all dvr channels are fine just when the output through the rf modulator to the tvs thats all. its like ..u ever see video that has noise (normal noise) then it smoothens with a slight wave then back to noise again hard to describe. sort of a wave. its not still.

Hi lads. got a question about remote control extenders to control the DVR from every room that has a tv? i have a cat 5 run to the house which is used for the tv output via dvr but theres some pairs left can i is it possible to put a IR bud on dvr end and the RF reciever on the other end. would this work for the whole house or does it have to have to have transmitters as well next to the tvs? wanting a cheap way to do this effectively. glad of anyhelp

got a dvr output tv modulator to tvs in house , the problem that i have since installing the dvr is a hunting overlay picture its not noticeable to the novice but i notice it it like it stop starts. output is baluned via cat 5 run to the modulator then is connected to the UHF distributor to multiple tvs in the house. the DVR is a Dahua 16ch hope ye can help lads.

hi folks reporting back on the dahua dvr got permission to remove seal and everything looked ok i disconnected cables and reconnected and made sure all was tight. reformatted HDD again seems to be no problems at this stage. It was a SATA WD caviar blue 500gb. good quality drive. thanks for tips fellas.

hey tomcctv yeah got it from adata/qvis came with 500gb hdd hope it will be as simple as a loose cable will see what support says give me permission to look in it. cctvlad

disabled all alarms formatted hdd - not recording right now so problem must be continuing have to talk to dealer support, cant get into dvr without breaking seal sticker just yet interesting it may not be fast enough or HDD not on supported list anyone know this one?

thanks for chiming in about it. yeah it comes up with the 500gb hdd but it goes again and beeps no disk i havent opened it yet and it does playback video so there must be a HDD in it the reason i haven't checked yet because of the seal. suspect this is a deeper problem also i cant get into device config (remotely) to turn off the alarm for now. PSS keeps hanging on that. could do with rorys help or sean