cableguy

Hello! Did you figure out to solve the problem ? Follow the steps. In entrapass 1) Setup the Gateway 2) Setup the Site + Put the communication port. ( With KT300 you can connect with RS232 or With a module converting from RS232 to RS485) 3) Setup the Controller (critical to put the s/n on the box there) At the control 1) do your connections ( Careful to make the right pin connection) 2) do a hard reset (make a jumper from RL1 to DOOR-DOOR 1) If the Heart led is blinking 3 times you got connection with the pc, you can always check the small yellow led rs232 or rs485 will light (left side of the controller). If you need any further help pm me

Hello guys Do you have any good seller for Thermal Cameras ? (not PTZ) and also a nice proffessional software that can support them. Also because the network will be made by fiber optics do you have something in mind that i can take care of it ? They will be about 120+ camera few thermals and whole perimeter is about 6meters. regards

Hello my dear friends. I am facing a new project that need 10 km camera view and a software for fire detection. Do you have any product on ur mind? i dont care about the brand famous or not much famous. And also i have been asked to answer a lot of times to trasmit video throw GPRS modem.... how is possible that..... as i know u can only send still image or a small amount of video.... or more better an alarm singal.... regards spiros

If u go IP solution u can simple use a good computer and a nice software like nuuo and milestone ( i sayed those cause i have been use both softwares). Or simple you can go with NVR

nice tools thx. I have use twice milestone in my project but i didnt know that they got tools like that

have u try to download ActiveX for mac?

Hello m8. As i know an active balum can go more than 600m (2000ft) singal. Just search a bit on the forum and u will find alot.

omg i was meaning about 6khm The customer dont care about the cost that much..... because he want about 8 thermal camera. Also he dont want any copper cable in the network expept those in the Control room........ I think the software must got some thermal alarms, and also can handle few high quality analogue camera and also motion detection. Thx alot for the info i am checking it right now.

Hello guys long time to be on line i was around all the time now i am back in my office. "home sweet home". I got a problem but i cannot found any solution my head is going to blow up. In a project we are using 21 camera. 2 * Analogue IR camera (Brand MINKING i dont remeber the model but is for long distance). 2 * IP server (single channel) Acti i think model 2100 19 * IP camera Samsung SCC-C6475P The most of the connection are wireless and the AP that we are using is ALVARION. The system has been test with nuuo and milestone Software but the problem is the same. THE problem is that we are loosing connection with 3-4 cameras. the 2 has problem because the UTP cable is about 70m-85m. the other 2 cameras are connected straight to the AP (Alvarion) but listen that, When i connect my laptop with the camera everything seems work really good i am not loosing a single "PING", but when i connected to the AP i am loosing a lot of and the screen doesnot even reach to the control room. by the way when i am in control room and ping the AP is loosing a few ping's. If i disconnect the camera and connect a small laptop and do a file trasfer everything work fine and when i am ping the AP is not loosing a single ping. I think from my experience that the problem is not the CAMERA. The problem coming from AP because the LIVE STREAMING.The IP Camera is simple without a QoS (Osi Model) and the laptop got top higher layer at the osi model with QoS. But from the company that represent alvarion in Greece says that their NETWORK work really fine. Can you please help with any ideas? P.S. Btw do you know anyway that i can solve the problem in the camera that the cable is around 70-85m? I am using a switch in the start but its doesnot help a lot. Best regards to all!

Maybe a problem occurs cause QoS?? because when u tranfer a file across the network doesnt matter the queue that will arrive first, but in a live motion picture its count and if u miss one packet the network (camera or ap) getting confuse........ maybe i am saying bull****s

i am think the same that the problem became from network...... But i cannot get it how is possible to plug a computer instead of camera and not loosing a single ping when we try to sent a big file to another computer in the network and when we plug it back nothing no picture from the camera.......

Hello. You can fill the DNS setting in your router so when its going online to communicate with the DynDNS site that you have assign. I think you can change the port on the DVR at least of the most that i have install they do. You have to port forward the specific port of the DVR that you have assign into your router. BTW you have static or dynamic IP? Its easier with Static ip because you dont need to assign DNS, you just port forward the ip of your DVR for example... IF your router has internal IP 192.168.1.1 then your DVR must go something like 192.168.1.x ( where x a number of your choice but be careful to be in the IP POOL of your router). then you need to port forward the PORT that you have input to your DVR and finally to fill the DNS on your rourer..... if your router does not have DNS setting you can fill those in your DVR. I think that help you a bit.

Hello cctvusers. Could you please give me or tell me few Outdoor Speed Dome Day/Night models with Auto Panning. I'm interesting for brands like Samsung - Panasonic - Sony - Pelco. Badget around 1000-1500 Euro. thx alot

this come looking like is came out from a toy park.....

Hello i got a new project and i have stack what equipment much be use for the best and cost effective solution. The camera must be install about 1000m from the control room. 1. solution is that to use IP camera with router and omni antenna at the control room.. (but i a don't prefer to use PC). 2. If i will use UTP is going to be a bit expensive the installation of the cable. And also do u know and medium quality Balum that i can use... any other idea?

My opinion is that the best u can do is to use at least 2A for the 700mA and at least 1A for 300mA (better use 2A too)...... Once in project i was i got problem with the supply at night. The supply was work perfect on Day but when the night come and the camera was need to operate with the IR the result was awful....When i change all the supply's from 500mA - 700mA that camera was need to 3A-4A the result at night was much much better.

Hello from then Snowy Greece. I am new here and i think i will stay for a long time i found very useful thinks inside here. So here is my question i have made a project with 8 cameras with UTP. The last camera is about 1km far from DVR i use active balun. Ok everything working perfect in the day light.... BUT in the night! i got horizontal black lines... The image quality is not the best cause the photo are taken throw ethernet..... Do u have any idea why that happen and how i can correct it? thx alot and nice work u done here.

Each build got his own electricity panel... and only that build that is the control room inside got electricity fail. I have measure the volt at each camera and i got 220V+ so i dont think is electricity issues..... So the only possible problem is the power supply, i think i use low in Amber power supply (cause the manufacturer write on manual 600-700 mA )........ is possible the active balun that i use make the problem? I am using one active balun in control room and the other in the middle of 4 cameras and from that active balun i am using a pair of passive balun for each (4) camera's. i try with or without the passive and still the problem exist but i didnot try without unplug the active balun too...... cause i am think with that try i will make more interference . Very first project >< bad choice to se lect a big one :S or at lease with UTP and that distance.... BTW how long can RG 59 go? is any amplifier ?

ok i change the power supply from 12Volt 1A to 12 Volt 4A i hope that is enought......but i cannot check it :S cause the central electricity on that building was down today....... i hope tomorrow will be ok so i can check it.. pm: thx again for ur help guys

First of all really!!!! thx for the replies here we got i hope that helps a bit yea but in really really slow from up to down sorry i am new in cctv nope i am using PAL version nope every camera got its own power supply about 12Volt, 1A in every camera i have put plug with 220volt and i attach to each plug its own power supply one for each camera.