kalpesh_nikumbh

The latest firmware for this product is version 4.40.1 http://www.axis.com/techsup/cam_servers/cam_206/firmware.php Kalpesh India

If the camera has set on NTSC and is viewed on PAL monitor ( & vise versa)... may this proble occures !! Have you checked that?? I don't think there is manoj problem in d cam. small stting issue only Kalpesh India

Welcome!! Kalpesh India

definitly not!! Kalpesh India

Why just insisting on NVR...?? Kalpesh India

So isn't that solution suggested is not worthy?? you can have stand alone/ separate 8 chanell switch for networking!!! What did you say? Possible solution: why cann't you go for Client-sever archtechture!! Let live strems record in server centrally... and have three PCs with AXIS Client software!! ( where in those three display monitos been pluged!) Instead of viewing live ...Playback the respective cameras with conveniont time to you!!! Kalpesh India

Thanks for the Invitation Tina!! Welcome to the forum!!! Kalpesh India

Hi Welcome !! Kalp.

wel come!! Kalpesh India

Hey thewireguys!! You wanna suggest 2 replace 4 camers with single!! That's nice!!! If that cannot possible and req....4 diffrent cams in difrent areas.... option 2 : But as he said ...budget is very low...he cam go for AXIs 207.. cheepest & Coolest MPEG-4 IP cam in AXIS. On prise could not comment ...since i works in India. Kalp.

http://www.crn.com/hardware/209904446 what did you say!! kalp.

Cool dopalgangr, After reading this..... my i exactly looking like ...what you have added in your avatar!!! your ans. is yes!!! Kalp.

Hey Scorpion !! I shared this with my friends here in mumbai , India...and they thought it's coool!! May be such ( rigid) tech. can be used for counting no. of commuters in the local trains here........ they are very much overloaded all the time. kalp.

Cool!! a ship with marines and garment with button!! Kalp.

kalp.

Ooooooooooops sorry wrong file attached!!! Kalp.

Hi zmxtech, Go to Setup on the web page ...it's very simple bro!! Kalp.

so Option No 1 : PTZ with video over coaxial + the PTZ controol signal over same cable with some properitaory protocol ( coaxitron etc) Option No 2 : PTZ with video over coaxial cable PTZ controls --> cables from Pan tilt motor ; motorised zoom lens cables to PTZ receiver ....which then pass RS485 control signal from this RX to DVR/keypad!! PTZ motor cables includes AUX + , UP , Down , Left , right , auto & ground Zoom lens cables includes zoom in , zoom out , focus far , focus near kalp.

certainly would write about Kodicom.... 1. PC / card based Diginet system 2. Linux based KSR system... till 2 yrs back ..when client use to ask upto cool 4 x 80 GB hard drives... KSR s where fine .....but suddenly they upgrade there firmwares...and here all problem start... they now supports 4 x 500 Gb..but just useless!!! about Diginet...ya ! i always have good experience with the product... only major problem was the heat generated during the continuous operation of the system.... If you have special industrial casing (Like Pelco DX series DVRs have)....they are dam Good. belive me our service center in india use to replace avarage 1 KSR every day!!jocks apart. Have no experience with Geovision yet. Kalp.

Hey scorpion!! So what happen to him then?? is he got the access there??? Kalp.

Wel come Keith sir!! u r of my father's age!!! he also started working around that time only... I born in 1980!!! but studied those tube type devices....never saw them!! may be that time those cameras needs to carry over shoulders!! or like DG sets?? Kalp.

Feel Safe....................... Kalp.

Wel come!! Cheers!! Kalp.

Check out your DVR Time zone... by default it is what d manufacturr's have!!! Kalp..

Wel come peter!! Kalp.