Jump to content

Search the Community

Showing results for tags 'controller'.


More search options

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type


IP Camera Forums

  • Welcome
    • Introductions
  • IP Systems
    • IP/Megapixel Cameras and Software Solutions
    • HD Analog
  • Digital Video Systems
    • General Digital Discussion
    • DVR Cards and Software - PC Based Systems
    • Computers/Networking
    • Digital Video Recorders
    • Dashcams - Mobile DVR's
  • Video Surveillance Systems
    • System Design
    • Security Cameras
    • Installation Help and Accessories
    • Video Transmission/Control Devices
  • Analog Video Systems
    • General Analog CCTV Discussion
  • Access Control Systems
    • General Access Control Discussion
  • Other Forums
    • Test Bench
    • Questions about this site
    • Trade Shows & Conferences
    • Classifieds

Calendars

There are no results to display.

There are no results to display.

Find results in...

Find results that contain...


Date Created

  • Start

    End

Last Updated

  • Start

    End

Filter by number of...

Joined

  • Start

    End

Group

WEBSITE

FACEBOOK

SKYPE

TWITTER

YOUTUBE

Found 1 result

  1. SaadMasood
    I am controlling my CCTV system from C100 Keyboard, see the picture in attachment. I forgot the password and was unable to access from web. I thought to give it a factory reset then. Unfortunately I could not find any reset button and I tried accessing it from console RS232. Set baud to 38400 and accessed. I searched over net and found that I should set environment varirable like below from UBOOT. => setenv stconfigignore true=> saveenv=> reset I did the same but my keyboard got stuck. U-Boot 2008.10 (Jun 27 2011 - 09:46:43) I2C: ready DRAM: 128 MB Manufacturer ID : 0018 Device ID : 009F Device Code 2 : 0018 Flash: 0 kB #SF: Got idcode c2 20 18 ##In: serial Out: serial Err: serial Net: FTMAC110#0 Hit any key to stop autoboot: 0 #SF: Got idcode c2 20 18 16384 KiB MX25L12845E at 0:0 is now current device ################################################################### Starting application at 0x04000000 ... Uncompressing Linux....................................................................................................................................................................................................... ................................................ I tried some burn in option and accidently removed the linux image.. ---------------------------------------------------------------------------- NVI Technology Corporation CPE Burnin Program v0.2.5 Platform: GM81262210 Cache: Disabled PLL1: 800 MHz PLL2: 540 MHz DDR: 800 MHz CPU : 540 MHz HCLK: 270 MHz PCLK: 135 MHz UART: 1 MHz H.264: 270 MHz MPEG4: 200 MHz STXWAMODE: RAO=1, STMWA=x ---------------------------------------------------------------------------- ( 1) DDR Test ( 7) Watchdog Rest Test (10) I2S Module1 Test (13) LCD Test (14) Query RTC (18) SAR ADC (22) Enable Cache (35) OTG 210 Test (50) MCP Clock Setting (51) FCS Test (61) I2C Read/Write (62) Change Cache WA_Mode (71) Address Read (72) Address Write (73) Burn UBOOT image (74) Burn Burn-In image (75) Burn Linux image (76) Burn Loader image (77) Burn fresh spi flash (78) BootFromSD (79) BootFromUSB (80) UBOOT, Linux Command>> Command>>75 File Name must be <linux> >>> Please select the storage : 1. SD card 2. USB OTG Mass Storage Incorrect input! Choose SD card. header address = d6000 Load image from SPI-NOR offset 0xd6000 to sdram 0x4000000 ...SD Card is not exist on device C. ...Please to Insert Card Command initial Cannot open file for reading image file(linux) size == -1 start to erasing old image... start_sector = 214, sector_cnt = 100001 Now I need the image and if anyone could please share the procedure to burn in.. I need your help please.
×