PoorOwner 0 Posted March 27, 2009 I used a 3/4" bit to drill through the siding of the house.. it's was big but required to fit the siamese + BNC. Now I was wondering if anyone has a favorite way to seal it back up? spray foam? foam rod + caulk? I do want to be able to remove it incase I need to change the camera.. (the BNC connection I shoved inside the attic). Share this post Link to post Share on other sites
C7 in CA 0 Posted March 28, 2009 Of the two choices I would use foam rod + caulk. Spray foam is great but the few times I have had to remove the stuff was no fun. The caulk would take paint better too I bet... How about being the envy of all your buddies and do it like this : Share this post Link to post Share on other sites
wisp_engineer 0 Posted March 28, 2009 Foam rod and caulk could work. Usually for holes in wood siding and what not we just use paintable caulk. Be sure it is paintable otherwise the paint won't adhere to it should the homeowner decide to paint it. Like C7 said though, using an outdoor rated outlet box with a gasketed cover is the way to do it. You can even install a gland nut on the knockout where you run the cable through to make sure it is sealed tight. Share this post Link to post Share on other sites
scorpion 0 Posted March 28, 2009 I just use caulk, or silicone sealant. I would only use foam spray if R value was of the essence. I just ran in to this for the first time! I was drilling in to a block wall when styrofoam came pouring out. It looked like someone cut open a bean bag chair! Here I am drilling on a ladder, and I am covered in snow! LOL! What a pain in the neck, but three feet lower! Share this post Link to post Share on other sites
C7 in CA 0 Posted March 28, 2009 I was drilling in to a block wall when styrofoam came pouring out. It looked like someone cut open a bean bag chair! Here I am drilling on a ladder, and I am covered in snow! LOL! What a pain in the neck, but three feet lower! HaHa. Was it a block wall with styrofoam in it, or was it a syrofoam wall that has been plastered? We did a winery with styrofoam walls. They were about 18" thick! Share this post Link to post Share on other sites
sviviani 0 Posted March 28, 2009 like they said, just make sure it is paintable. Share this post Link to post Share on other sites
DVR MAN 0 Posted March 28, 2009 I use a product called Duct Seal. It is a non hardening plumber putty like substance. It seals against dust, noise, drafts, and moisture. I press it in around the conduit, or wiring and thats it. Never had a problem. It sells in one pound blocks at Home Depot. My .02 Share this post Link to post Share on other sites
scorpion 0 Posted March 28, 2009 It was a block wall http://en.wikipedia.org/wiki/Cinder_block The hollow section was foam filled! I was a mess when I was working on the inside of the place! I tried my best to "pat" myself down, and shake it out of my hair! I wish I had that event on a camcorder! Maybe I should start doing my installs live streaming with a web cam! Share this post Link to post Share on other sites
wisp_engineer 0 Posted March 28, 2009 I use a product called Duct Seal. It is a non hardening plumber putty like substance. It seals against dust, noise, drafts, and moisture. I press it in around the conduit, or wiring and thats it. Never had a problem. It sells in one pound blocks at Home Depot. My .02 After I posted my reply I thought about duct seal as well. We use that to seal holes on communications sites where the cables pass through the entry port, if there are extra holes or spaces. Keeps the bugs out Share this post Link to post Share on other sites
DVR MAN 0 Posted March 29, 2009 I use a product called Duct Seal. It is a non hardening plumber putty like substance. It seals against dust, noise, drafts, and moisture. I press it in around the conduit, or wiring and thats it. Never had a problem. It sells in one pound blocks at Home Depot. My .02 After I posted my reply I thought about duct seal as well. We use that to seal holes on communications sites where the cables pass through the entry port, if there are extra holes or spaces. Keeps the bugs out Yup! Great stuff. If you need to remove it, you just pull it out, then stick it back in when you are finished. I bet you can paint it too. Share this post Link to post Share on other sites