willo 0 Posted January 3, 2010 hi can anyone shed some light on how to set up this camera tried just about everything tools at my disposal are r323 to r422 convertor r323 to rs485 convertor pc based cam controller and software supporting pelco p+d,tried honeywell site but a bit confusing as one set of docs tells you to use 422 and one tells you to use 485 inside of camera connections are +vh/ovh video/vid.gnd +vs/ovs data+/data- sync/s.gnd.can get picture on screen fan and heater connected and working and it goes through set up dance ,no info appears on screen just pic, the boards inside of camera have vc472v3 which has the pinouts on it 1-8 and 1-4 the board below has vc471v3 this has lk1 with jumper on but only two pins which it bridges both this is next to small battery on top board i.e 472v3 there are six pins with a double jumper on one side reads tp term and the otherside reads on /off and this is also labelled lk1 the double jumper is set to on .on honeywell website it shows all connection methods but none appear to match up with mine as they seem to have an nvt connection on there and mine does not also it mentions coax or 485 telemetry and that it auto sensors which one is connected??? when i recieved dome it had all wires conected into it apart from data+/data- sync/s.gnd so i assume it was run originally thru coax but the person i bought it of is as clueless as me as regards to any other equipement that may have been with camera as he was just told to take camera down from its position as building was being demolished.am i missing some kind of convertor as when i try to control camera using 485-422 it will not do anything thanks in advance for any help as i m not to cued up on protocols and such so please keep ans as untechnical as poss please thanks john Share this post Link to post Share on other sites
willo 0 Posted January 4, 2010 anyone ??????????????????????? Share this post Link to post Share on other sites
willo 0 Posted January 6, 2010 i have obviously been mis informed about this being the best site for cctv help seems such a shame to lash it in the bin Share this post Link to post Share on other sites
tomcctv 190 Posted January 6, 2010 i have obviously been mis informed about this being the best site for cctv help seems such a shame to lash it in the bin thats am old ptz last time i fitted one of these was over 10 years ago. you need the vcl ptz controller to operate your camera. so its back to ebay for you and look for a vcl ptz control unit. but it will cost. were are you ??? Share this post Link to post Share on other sites
willo 0 Posted January 6, 2010 thats for reply begining to give up hope,im in liverpool uk can you shed any light on the coax/r485/422 as on the honeywell site it states that it can use either but tried with both 422 and 485 but dont seem to get any joy tried all the bauds 2400/9600 but with no movement?if i can trackdown a controller will this work with the coax or twisted pairs from data + data -as you can see not to cued up on cctv thanks again john Share this post Link to post Share on other sites
willo 0 Posted January 9, 2010 thanks guy for all your answer totally overwehlmed by the amount of answers i recieved one vcl camera destined for bin Share this post Link to post Share on other sites
woodic 0 Posted August 19, 2010 Hi. Its a shame if you've chucked the camera out. I've done quite a bit of work with these VCL\Honeywell cameras including writing a control program for Windows. You just need a 232 to 485 convertor (about £10.00 of Ebay) and a PC running Windows obviously. Share this post Link to post Share on other sites
markymark2011 0 Posted July 20, 2014 did u ever get this sorted and what softwaer do u use Share this post Link to post Share on other sites
masoud1313 0 Posted July 26, 2014 Your question is not clear!!!! <a href="http://www.irankg.com">cctv</a> <a href="http://www.parsiavpn.com">buy vpn</a> <a href="http://www.e-gol.ir">buy flower</a> <a href="http://www.aryadidcctv.com">cctv</a> Share this post Link to post Share on other sites
