Jump to content
WannaBeGeekster

Help with PTZ/Camera Control on Panasonic setup

Recommended Posts

Hello,

 

I have the following equipment:

 

WJ-HD316 DVR

WV-CW974 Camera

WV-CU650 Controller

 

I have the WV-CU650 controller talking to the WJ-HD316 DVR just fine. The issue is the communication from the WJ-HD316 to the WV-CW974 camera. I have a CAT 5 cable ran from the camera to the DVR. I am using a Rj12 Keystone in the junction box where the camera balun is located. I am using the following six wires for the Keystone jack:

 

1. Green / White

2. Orange / White

3. Blue

4. Blue / White

5. Orange

6. Green

 

I have verified that the colors on the RS485 cable coming from the camera are as follows:

 

1. Empty

2. Red

3. Orange

4. Yellow

5. Green

6. Empty

 

I have terminated a RJ12 connector on the end of the CAT5 cable that plugs into the DVR. The colors are as follows:

 

1. Empty

2. Orange / White

3. Blue

4. Blue / White

5. Orange

6. Empty

 

The DIP switch settings on the back of the DVR are as follows:

 

SW 1: On - Terminate

SW 2: Off - 4 Wire

SW 3: Off - 4 Wire

SW 4: On - Terminate

SW 5: Off - 4 Wire

SW 6: Off - 4 Wire

SW 7: On - PSData Terminate System Controller device (System Controller is working just fine)

SW 8: Off

 

The camera is configured for 4 wire communication and the camera is also set for being terminated also. They are single runs. No daisy chaining going on here.

 

One camera is configured as Unit # 3. The other is configured as Unit #4.

 

The System is setup as Unit #1 and the controller is configured as Unit #2 in the WJ-HD316 setup menu.

 

Baud rate is set for 19200. I have tried both RS-485 ports on the back of the unit. I am getting the configuration menu when I disconnect the power from the camera and plug it back in. It only stays up there for a short bit. The WV-CU650 is supposed to be able to go into the camera setup menu by the following keys on the device: Menu > Camera Setup > Enter > F1. When I do that On has a > by it for a second then goes away and of course the menu never shows up.

 

So I am wondering if there is a compatibility issue or something else I am missing here. If anyone has any experience with this beast I would appreciate a helping hand here. Would even be willing to make it worth your time if you need something.

 

Thanks,

 

WBG

Share this post


Link to post
Share on other sites

why are you messing about with all those cat 5 cables blah blah blah?

 

I have all that gear you have and loads of pany domes, and they all use up the coax one wire?

 

ptz - dvr controller using up the coax?

 

no need for anything else, the dvr sends the signal for the ptz through the coax

Share this post


Link to post
Share on other sites

the only cat5 cable I use is 2 wires to the dome for video via baluns, this is still "up the coax" put the pins on dome back to normal set the dvr to coax for the ptzs

Share this post


Link to post
Share on other sites

Awesome! I had a feeling today that I was making things harder than they should be.

 

So I want to set the Unit # Jumpers (the block of to all off. Which is multiplex mode basically.

 

Ok I will try this once it stops raining and see how it goes. I was trying to do that today and couldn't get up to the second story roof as it rained all afternoon.

 

Thanks! Will report back how it goes.

 

WBG

Share this post


Link to post
Share on other sites

yes please update. I will help you get your settings right, as I have one of them domes beside me right now, and the exact same equipment that you have too., and yes its not very nice on ladders in the rain!!

 

and yes the pins need to be how they were when you took it out the box.

Share this post


Link to post
Share on other sites

Great news! That is exactly what the doctor ordered. Setting the dip switches to all off made it work immediately. After that is was a simple matter of getting the autotracking setup and the system was rocking and rolling. Very very nice setup. I am very impressed. Wish I had $75k per year of sales for Panasonic so I could become a partner with them.

 

Anyway, thanks again for your help! Was very useful!

 

Thanks,

 

WBG

Share this post


Link to post
Share on other sites

hi I don't no if I am posting in the right place but I have a Panasonic wv-cw860a/g I was wondering if I could just connect it to my rs845 connection and control it throw the dvr. my dvr is an Atlantis (qvis) 16ch would this work or do I need a decoder and a controller? please help

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×