davidafi 0 Posted August 6, 2014 I know sku 315912 at DX works with my NVR on i9 protocol.i9 is not mentioned when i read the camera specs. I am trying to untangle this little mess as well. I can't find anything anywhere that explains what I8 or I9 is all about, and I have just discovered I16 as well. Whose protocols are these and where can you get any info about them? Share this post Link to post Share on other sites
pb617 0 Posted August 7, 2014 can / did you fotmat the drive ? Are you powering the drive externally? ie using a USB hub? Seems off the point, but what protocol are you using from the cameras? The drive has a power adapter, it's not USB powered. The cameras are using Onivf for a protocol. I am using 4 Dahua IPC-HFW2100 and 3 Dlink DCS-2132L (WiFi). This is the drive i'm using: http://amzn.com/B00834SJS0 Also, i tried using the Network Video Monitor Software that came with the Mini NVR and tried to make changes this way, but the settings don't apply after i hit "Save Parameters". When i go back into it, they are back to the default settings. Is there a reset option? Maybe i can set it all up again. I have rebooted it several times. Not sure what else to do. Share this post Link to post Share on other sites
davidafi 0 Posted August 7, 2014 The cameras are using Onivf for a protocol. I am using 4 Dahua IPC-HFW2100 and 3 Dlink DCS-2132L (WiFi). I had the same problem. Eventually after much fiddling I got a firmware update for the NVR and problem solved. It is now running V4.0[20140416]. The cameras are now using I16 protocol. (Whatever that is??) From what I can understand, a lot of the config options are stored in the cameras not the NVR. If the protocol is not working properly this information doesn't get sent to the camera when you hit Save. I also eventually realised that the manual (even though it is not specifically for the Super Mini NVR) actually states that Motion Detection and various other functions are not supported by Onvif protocol. RTFM! Share this post Link to post Share on other sites
Pizza_m79 0 Posted August 8, 2014 That is what I also understood. Onvif is not what's needed instead the same as the xvision XC range cameras... Share this post Link to post Share on other sites
Szymon_Zy 0 Posted August 9, 2014 Hello Could you post in this thread model and links to cameras that work or does not work with motion detection using this nvr? For example: HC-602 does not work -link http://www.aliexpress.com/item/Mini-Bullet-IP-Camera-1280-720P-1-0MP-ONVIF-Waterproof-Outdoor-IR-CUT-Night-Vision-Security/1938771720.html I'm interested which cheap cameras work with motion detection but now it is impossible to get this data anywhere .... Share this post Link to post Share on other sites
hendrik6073 0 Posted August 10, 2014 maybe there is a way to find out the exact (sub) protocol the camera supports, than find the update for nvr. i bought a cam that supports i13, als got the login information to download the i13 protocol update. now NVR does i13 and motion detection with this camera. ================== following website: www dot 115 dot com/?lang=en (Please change the two dots into punctuation.) The user ID is 360811909, and password is flm1991913. Please download the rar file named "i13.update" in the folder named "miniNVR". ================================= Share this post Link to post Share on other sites
Szymon_Zy 0 Posted August 11, 2014 Could you post a linkt to this camera? Share this post Link to post Share on other sites
hendrik6073 0 Posted August 11, 2014 yes http://www.ebay.com/itm/161287999991?_trksid=p2060778.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT Share this post Link to post Share on other sites
Pizza_m79 0 Posted August 11, 2014 This mini NVR seller writes: "The NVR can only realize simple functions , like video play, through ONVIF protocol. But not all onvif protocol cameras can realize motion detection with this NVR. If you need to save other settings like MOTION DETECTION, CAMERAS SHOULD HAVE PRIVATE PROTOCOLS WITH THE NVR. PLEASE DO CONFIMR WITH US BEFORE PURCHASEMENT! For example, for TI W series, please use i9, and for HX series, please use i13" http://www.ebay.com/itm/N62-8E-ONVIF-Mini-NVR-8X1080P-960P-720P-HD-Network-Video-Recorder-Audio-In-P2P-/121208755977 Share this post Link to post Share on other sites
hendrik6073 0 Posted August 11, 2014 okay, maybe we can ask to post the 'flavours' he has ? Share this post Link to post Share on other sites
Pizza_m79 0 Posted August 11, 2014 I asked him to make it simple and post what HD cameras works with the NVR and supports motion detection, still no answer. Share this post Link to post Share on other sites
hendrik6073 0 Posted August 11, 2014 maybe he knows a way to find out what private protocol is active ? i do not know the trick Share this post Link to post Share on other sites
Szymon_Zy 0 Posted August 11, 2014 How did you install this update? This is not a rar file i13.update - my nvr if i try to update says this is wrong file. I got response from escam.cn that their cameras are motion detection compatible with their mini nvr (i own that one 8ch). I notice one more thing this nvr esata port is only data! No power, you have to grab power from usb! So you have to use cable like that: http://www.ebay.com/itm/New-Hard-Disk-Drive-SATA-22Pin-to-eSATA-Data-USB-Powered-Cable-Adapter-0-5M-HIYG-/221440474130?pt=US_Drive_Cables_dapters&hash=item338ee17c12 instead of regular without usb plug. Share this post Link to post Share on other sites
Pizza_m79 0 Posted August 11, 2014 "Thanks for your message,our W series,HX series cameras will be perfectly compatible with this mini NVR. It means that when you connect these series cameras to the NVR,the motion detection function can be available. For W series cameras,you can refer to the below link: http://stores.ebay.com/seeingtek/5mp-3mp-1080p-Ip-Camera-UC-TI-/_i.html?_fsub=4486802016&_sid=1166060466&_trksid=p4634.c0.m322 For HX series cameras,you can refer to the below link: http://stores.ebay.com/seeingtek/Ip-camera-Chrome-Firefox-Win8-/_i.html?_fsub=5079780016&_sid=1166060466&_trksid=p4634.c0.m322" Share this post Link to post Share on other sites
hendrik6073 0 Posted August 12, 2014 How did you install this update? This is not a rar file i13.update no it is not a .RAR, just update under settings using the file, than reboot. Share this post Link to post Share on other sites
hendrik6073 0 Posted August 12, 2014 i have enabled send mail at motion detection function on all camera's. some send attachement, some don't anybody else with same behavior ? thanks Share this post Link to post Share on other sites
Szymon_Zy 0 Posted August 12, 2014 OK. To perform update you have to attach hdd. Share this post Link to post Share on other sites
hendrik6073 0 Posted August 13, 2014 anybody know how to factory default a bullit cam ? mine is in a reboot loop, can't ger it out Share this post Link to post Share on other sites
a.onderwater 0 Posted August 14, 2014 Hello, anyone connected foscam camera's (without ONVIV) to the NVR??? Share this post Link to post Share on other sites
panapro 0 Posted August 18, 2014 Hello CCTV'ers I also ordered this mini NVR. (http://www.aliexpress.com/item/4CH-8CH-Mini-NVR-IP-Camera-Recorder-Surveillance-4-CH-8-CH-1080P-960P-720P-HD/1704796387.html) I am using it with these 2 camera's (http://www.aliexpress.com/item/Support-Iphone-and-Andriod-3-7-mm-Korea-Pinhole-Lens-1920-1080-H-264-1080P-Micro/1859184041.html) and (http://www.aliexpress.com/item/2-8-12-mm-Varifocal-Lens-H-264-2-0-Megapixel-Waterproof-Vandalproof-Dome-1080P-2MP/1260729632.html) I get moving pictures from both these camera's as long as I don't enter full screen mode, in full screen mode the picture freezes till I go back to multiviewer mode. I'm also not able to get the motion detection recording working. Another problem is that I only can play back the camera connected to channel1, the other camera's show a black picture in playback mode. Is there anyone who has got the same problems? Share this post Link to post Share on other sites
nadiel 0 Posted August 20, 2014 Hello. Does anyone know if I can connect a network relay card or usb relay card to this nvr to use alarm output? Thank you. Share this post Link to post Share on other sites
hendrik6073 0 Posted August 20, 2014 i dont think so, i think you have to connect those to the cam itself Share this post Link to post Share on other sites
power323f 0 Posted August 20, 2014 Hello, my mini nvr, not detecting camera (Foscam), I have placed all network parameters correctly, and even so I do not detect any camera. Anyone know where can be my mistake. thank you Share this post Link to post Share on other sites
hendrik6073 0 Posted August 21, 2014 can somebody repost the credentials to set up a telnet connection with NVR ? it was as a link on this board, not working anymore Share this post Link to post Share on other sites
