ryn0909 0 Posted March 4, 2015 here is the gui login screen Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 4, 2015 I've seen a similar screenshot in this forum! Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 4, 2015 Yes! viewtopic.php?f=3&t=44986&hilit=reset+password link to screenshot and link to pdf default password is 1234 but there are another post at this forum! Share this post Link to post Share on other sites
ryn0909 0 Posted March 4, 2015 yea i know the password for the gui login..... its the serial debug console that i cant figure out... ive tried all the typical pswd's Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 4, 2015 yea i know the password for the gui login..... its the serial debug console that i cant figure out... ive tried all the typical pswd's Stop boot from console use u-boot command & tftp server to download firmware from flash Share this post Link to post Share on other sites
ryn0909 0 Posted March 4, 2015 yea i know the password for the gui login..... its the serial debug console that i cant figure out... ive tried all the typical pswd's Stop boot from console use u-boot command & tftp server to download firmware from flash im not familiar with u-boot commands, can you pls explain to me? Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 4, 2015 im not familiar with u-boot commands, can you pls explain to me? Stop boot type printenv type help Share this post Link to post Share on other sites
ryn0909 0 Posted March 5, 2015 well i guess stopping the boot process is a little more complicated than i thought. i can see in the log that it gives 0 seconds to "press any key" and ive tried and tried and still cant get it to stop. i guess when i was getting the login prompt, it was from the "hot key sequence". which i did find a change in the logfile that shows the following...... [/size] debug-Message: nf_debug_category_add cate[sysman] log_str[0x00205f60] log_arr[0x00205fe0] log_arr_max_idx[3] [1] sysman-Message: nf_sysman_hotkey_init cmdline[console=ttyS0,115200n8 noinitrd rw ip=::::NFDVR:eth0:off root=/dev/mtdblock9 rootfstype=yaffs2 mem=120M eth=00:11:5F:06:80:61 fw_upgrade_temp num_ch=16 signal_type=ntsc model_type=ANF_1648 crc_ubl=99c953dd crc_ker=ab3ddeba crc_fpga=15a5290d pannel_type=ITX-5 rc_type=AVR4816-ITX hw_ver=MAFS116C ] sysman-Message: nf_sysman_hotkey_init _factory_default [0] sysman-Message: nf_sysman_hotkey_init _passwd_reset [0] sysman-Message: nf_sysman_hotkey_init _fwupgrade [0] sysman-Message: nf_sysman_hotkey_init _qa [0] sysman-Message: nf_sysman_hotkey_init _consol_enable [0] sysman-Message: nf_sysman_hotkey_init _is_nfs [0] sysman-Message: nf_sysman_hotkey_init _boot_mtd_num [9] sysdb-Message: nf_sysdb_init wait[1] load_data[1] I have figured out that the HOTKEY sequence is achieved by holding down DISPLAY, SETUP, and ANY NUMBER and plugging the power cord into wall. DISPLAY, SETUP, NUMBER1 = factory_default NUMBER2 = passwd_reset NUMBER3 = fwupgrade NUMBER4 = qa (fwdowngrade) NUMBER5 = consol_enable NUMBER6 = is_nfs (??) NUMBER7 = boot_mtd_num Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 5, 2015 From your log!!! U-Boot-1.2.0 (Mar 25 2010 - 18:51:36) I2C: ready DRAM: 256 MB unknown vendor=0 Flash: 0 kB NAND: Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 256 MiB In: serial Out: serial Err: serial ARM Clock :- 493MHz DDR Clock :- 408MHz [ANF1648 Initialize] [sPI INIT] System Reset Check..was passed [signal Type is [NTSC]] [ANF1648 Spot Init] [Pannel Type is ITX-5 ] [RC Type is AVR4816-ITX ] [Mac address [00:11:5F:06:80:61 ]] [before Shutdown => abnormal shutdown] Hot Key MAGIC_KEY_PASSWD_RESET [Tw286x Initialize / Signal Type : NTSC] [TW2865 dev[0x28] done] [TW2865 dev[0x29] done] [TW2865 dev[0x2a] done] [TW2865 dev[0x2b] done] [Fan On] [FB ADDR [0x8e000000]] Reading data from 0x7ff800 -- 100% complete. [MDIN240 Initialize] [** Warning ** HDMI/DVI DDC Edid CheckSum Error!!!] [** Warning ** Analog DDC Edid CheckSum Error!!!] [Video Output Infomation : Unknown Video Size Set Default 1024x768p60] [MDIN240 HDMI INIT] [set Output Video Clocks 27MHz] [Turn_On_DSP] [uART2 INIT] [uART1 INIT] Hit any key to stop autoboot: 0 Share this post Link to post Share on other sites
ryn0909 0 Posted March 6, 2015 what do you mean , from my log?? Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 6, 2015 what do you mean , from my log?? viewtopic.php?p=267331#p267331 Share this post Link to post Share on other sites
ryn0909 0 Posted March 6, 2015 lol you totally lost me, i have no idea what your are talking about Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 6, 2015 lol you totally lost me, i have no idea what your are talking about After start your dvr and then you'll see boot log Hit any key to stop autoboot: 0 in 3 second Then you in u-boot command printenv - for enviroment list help - for help Share this post Link to post Share on other sites
ryn0909 0 Posted March 6, 2015 ok the only problem is tha no matter which key i press, it doesnt stop the boot process..... Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 6, 2015 ok the only problem is tha no matter which key i press, it doesnt stop the boot process..... For ex: dahua use * in digit keybord (rigth) other may use specific key What COM port config on your PC? Share this post Link to post Share on other sites
ryn0909 0 Posted March 6, 2015 com port 5 115,200 8 N 1 none Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 6, 2015 com port 5 115,200 8 N 1 none So, find key or key combination to stop autoboot! Ex: hikvision use ctrl+u Share this post Link to post Share on other sites
ryn0909 0 Posted March 6, 2015 ill try my best to see what i can come up with Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 6, 2015 ill try my best to see what i can come up with Try! Share this post Link to post Share on other sites
ryn0909 0 Posted March 6, 2015 im trying as we speak.... isnt there a way to make a bootable usb that will stop the autoboot? Share this post Link to post Share on other sites
ryn0909 0 Posted March 10, 2015 ok so still no luck at getting it stopped. i dont think the commands are getting thru to the console until after it has passed the stop autoboot point. im using PuTTY, maybe its not configured properly? Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 10, 2015 ok so still no luck at getting it stopped. i dont think the commands are getting thru to the console until after it has passed the stop autoboot point. im using PuTTY, maybe its not configured properly? But after bootload you can enter login name & pass - so it's configured ok! Try in Hyperterminal on NCOM Share this post Link to post Share on other sites
ryn0909 0 Posted March 10, 2015 yea i guess you're right, it must b configured correctly... hmmm would you happen to know what it means when it says console mode enabled? its one of the hotkey modes Share this post Link to post Share on other sites
iTuneDVR 2 Posted March 10, 2015 I think you need try all combinaton & reset dvr ctrl+ [key] Share this post Link to post Share on other sites
