sichuan 0 Posted January 4, 2016 I'm about to receive a Q-See 16-Channel 8 Night Vision HD Bullet Cameras w/ 2 TB HDD HD DVR Security System. I exchanged an uninstalled Q-See 8-Channel/8 camera system for it because I decided that I would eventually need to add at least three to four dome cameras for both inside and outside, which would be in addition to the eight bullet cameras that come with the system. I realize that it's a low-end system and that we get what we pay for. I realize that digital is better than analog. I'm also aware that there are better systems available to the consumer. However, the system I chose is all that I need at this time. It will be for residential use. If necessary, I can always upgrade to a better system in the future. Running cables through the attic and down the wall to the secure bedroom poses no problems. My question involves the cable and power hookups once I run the cables to a small, secure bedroom. I want a neat installation. I'm a stickler for neatness and I don't want to simply run the cables through a hole in the wall and then to the DVR. Are there wall plates available for RG-59 BNC cables so that I can connect the BNC cables from the cameras to the back side of the plate and then run short BNC cables from the front side of the plate to the DVR? Do any such plates also have connections for the RCA cables and if so do they include the power source transformer? I've spent quite some time researching this issue but I don't know enough about it to do proper searches for what I'm looking for. I always try to solve a problem or determine what I need before I ask for assistance from other people. I'm not relying on others to do the work for me. I'm simply stumped. I did find this, which I can get from Q-See, Amazon or Home Depot. I just found it so I don't really know anything about it or what it will do for me but it looks promising. I assume it handles power only, which will tackle the power cable neatness problem, so I'm still looking for something to tidy up the BNC cable connections. http://www.amazon.com/Q-See-QS1018-Distribution-Connects-Cameras/dp/B004656PH2 (I realize that there are many similar power distribution boxes manufactured by other companies that may be better. I simply haven't gotten that far yet. I'm also researching the required power to each Q-See camera and whether I need a 10, 12 or 20 amp box. I've seen all three offered online). Please excuse my ignorance and thank you for your time and any assistance provided. Share this post Link to post Share on other sites
myiicu 0 Posted January 4, 2016 A rack mount BNC patch panel is nice and neat but will be cost and will add to troubleshooting time because of more connection points to fail. Direct connection from camera to DVR/NVR is better and the main wiring hole can look better with wall plate cable management. http://www.monoprice.com/product?p_id=12573 http://www.monoprice.com/product?p_id=3996 https://www.parts-express.com/single-gang-bulk-cable-wall-plate-white--261-152 Also, pull Cat5e/6 cable with that bulk Siamese cable (do not use premade Siamese) so you will be ready for IP... Share this post Link to post Share on other sites
sichuan 0 Posted January 4, 2016 A rack mount BNC patch panel is nice and neat but will be cost and will add to troubleshooting time because of more connection points to fail. Direct connection from camera to DVR/NVR is better and the main wiring hole can look better with wall plate cable management. http://www.monoprice.com/product?p_id=12573 http://www.monoprice.com/product?p_id=3996 https://www.parts-express.com/single-gang-bulk-cable-wall-plate-white--261-152 Also, pull Cat5e/6 cable with that bulk Siamese cable (do not use premade Siamese) so you will be ready for IP... Thank you, myiicu, for your prompt reply. I appreciate it very much. The wall plates shown in your links may indeed be what I want. I'll take your suggestion to heart and pull Cat6a along with the BNG cables. I've already wired the house with Cat6a cables in several rooms. Why do you suggest that I use bulk Siamese cable instead of Siamese cable with factory installed connectors? Wouldn't the factory installed connectors be better than using twist on or crimped connectors? I don't intend to use the Siamese cables that come with the system. I will instead use either shielded or double shielded Siamese cable. As far as the Siamese shielded cable is concerned, is solid or stranded core better? I assume that solid copper core or strands is better than copper coated metal. What about the shielding? Should it be copper or is an alternative such as aluminum acceptable. Cost is not really a factor because as we all know, you get what you pay for. I'm more than willing to spend the amount of money necessary to ensure that my cables remain trouble free for as long as possible. Also, should I go with AWG 18 or is AWG 24 acceptable? I still intend to use a power distribution box to simplify the installation and provide a more aesthetic look for the power connections. I'd rather not use the power splitters so that I can be sure the cameras get the proper amount of power as some of my cable runs will be close to 100 feet in length. Again, I appreciate your assistance. At times I completely depend on the knowledge and experience of others and I'm thankful that you and others are willing to share it with me, along with your time. Share this post Link to post Share on other sites
myiicu 0 Posted January 5, 2016 A centralized power distribution box is the proper way to supply power to your cameras. Look for a unit with led indicators and resettable fuses for each channel. http://www.monoprice.com/product?c_id=110&cp_id=11009&cs_id=1100902&p_id=6875&seq=1&format=2 Make sure that the total power is enough to power all of your cameras. Check the power requirements (Amps) of each camera. Cameras with IR leds will require more current for night-time operation. I use mainly Belden 549945 Siamese (18g) with 2 pc crimp on or compression bnc connectors... viewtopic.php?f=6&t=45116&hilit=belden Share this post Link to post Share on other sites
