Trafic 0 Posted April 29, 2016 Hello. I own a dvr AverMedia Seb5108 Lite that I have not used one year and forgot the password. I know there are a masterpassord or hardreset but i did not find any documentation . On the pcb are two buttons and a few jumpers but I do not know for what. If someone can help me with some advice I would be grateful . Thanks in advance. Share this post Link to post Share on other sites
tomcctv 190 Posted April 29, 2016 Hi have you tried the master user and password. FIRST LETTER is capital Admin 111111 Share this post Link to post Share on other sites
Trafic 0 Posted April 29, 2016 Yes.. and 12346, admin admin, 000000... unsuccessfully. Share this post Link to post Share on other sites
judy-mavlon 0 Posted May 3, 2016 It's best if you can contact the vendor where you purchased it. Master passwords are not usually publicly posted for obvious security reasons. A lot times they have a tool to generate the master password, or it's a very unique string of numbers. Share this post Link to post Share on other sites
Trafic 0 Posted May 5, 2016 I'm the unluckiest man right now... I contacted Aver support and were kind enough to send me a password reset. But I did not get to use it because before to begin the password reset process, I installed a new HDD to prepare everything. (stupid mistake) After I installed HDD the DVR entered in a RESTART LOOP every 10s color bars appear(normal) but then when it should appear "loading ...%" screen it just restart , again color bars again restart..and so on)... No boot. I tried everything (another HDD, without HDD,some Recover firmware and firmware found on the Internet, but does not read USB Stick). Some ideas? PS: Sorry for my english Thanks Share this post Link to post Share on other sites
Trafic 0 Posted June 24, 2016 Hello. Can someone help me with an EEPROM (Boot) program(Dump) for AverMedia SEB 5116Lite or 5108Lite ? Thanks Share this post Link to post Share on other sites
Trafic 0 Posted August 25, 2016 Hello. After a lot of work I was able to connect the DVR to a laptop via RS232 and PuTty = > log file | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ,modify by scott ** MARVELL BOARD: RD-88F5182-NAS-3 LE U-Boot 1.1.1 (Aug 21 2009 - 17:14:33) C2A9 B version: 1.1.0.8 Vic Size = 0x8000000 DRAM CS[0] base 0x00000000 size 128MB Vic Size = 0x8000000 DRAM CS[1] base 0x08000000 size 128MB DRAM Total size 256MB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done NAND:devNum=3,mvBoardGetDeviceBaseAddr /home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/Board/boardEnv/mvBoardEnvLib.c 1191 scott test NAND ADDRESS = f6000000,/home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/USP/mv_main.c 894 enter nand_probe cmd_nand.c 1658 NAND mfr id ec at cmd_nand.c 678 NAND id id 75 at cmd_nand.c 679 1 flash chips found. Total nand_chip size: 32 MB 0xf6000000: 32 MB devNum=1,mvBoardGetDeviceBaseAddr /home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/Board/boardEnv/mvBoardEnvLib.c 1191 scott test NAND ADDRESS = f8000000,/home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/USP/mv_main.c 900 enter nand_probe cmd_nand.c 1658 NAND mfr id ec at cmd_nand.c 678 NAND id id 75 at cmd_nand.c 679 1 flash chips found. Total nand_chip size: 32 MB 0xf8000000: 32 MB Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 500Mhz Orion 1 streaming disabled SysClock = 166Mhz , TClock = 166Mhz USB 0: host mode USB 1: host mode pciIfNum:2,/home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/USP/mv_pci.c 628 PCI 0: PCI Express Root Complex Interface vendor id:0x11ab header_type:0x0, pci.c 471 PCI Scan: Found Bus 0, Device 0, Function 0 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x0, pci.c 471 PCI Scan: Found Bus 0, Device 1, Function 0 device id:0x6121, pci.c 479 CONFIG_PCI_PNP end at 502 in pci_hose_scan_bus PCI 1: Conventional PCI, speed = 33000000 vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 0 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 1 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 2 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 3 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 4 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 5 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 6 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 7 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x9413 header_type:0x0, pci.c 471 PCI Scan: Found Bus 1, Device 9, Function 0 device id:0x6010, pci.c 479 =pci.c 492 end at 502 in pci_hose_scan_bus i = 0 @@value = 243 i = 1 @@value = 243 i = 2 @@value = 243 i = 3 @@value = 243 i = 4 @@value = 243 i = 5 @@value = 243 i = 6 @@value = 243 i = 7 @@value = 243 i = 8 @@value = 255 i = 9 @@value = 255 i = 10 @@value = 255 i = 11 @@value = 255 i = 12 @@value = 255 i = 13 @@value = 255 i = 14 @@value = 255 i = 15 @@value = 255 video type = 1 Net: eth.c 133 egiga0 [PRIME] USB: scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... i=0 usb_get_dev_index i=0 usb_get_dev_index dev!=NULL iVendor 0 iProduct 0 devClass=9 IFClass=9 IFSubClass=0 i=1 usb_get_dev_index i=1 0 Storage Device(s) found Erasing Nand...Writing to Nand... done Hit any key to stop autoboot: 0 usb_read: dev 0 ** Can't read from device 0 ** ** Unable to use usb 0:1 for fatload ** usb_read: dev 0 ** Can't read from device 0 ** ** Unable to use usb 0:1 for fatload ** ## Booting image at 00400000 ... Bad Magic Number .... and here RESTART Share this post Link to post Share on other sites
Trafic 0 Posted August 25, 2016 Then I tried a reprogramming via TFTPD32 and stuck here ... ˙#NAND bootstrap __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ,modify by scott ** MARVELL BOARD: RD-88F5182-NAS-3 LE U-Boot 1.1.1 (Aug 21 2009 - 17:14:33) C2A9 B version: 1.1.0.8 Vic Size = 0x8000000 DRAM CS[0] base 0x00000000 size 128MB Vic Size = 0x8000000 DRAM CS[1] base 0x08000000 size 128MB DRAM Total size 256MB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done NAND:devNum=3,mvBoardGetDeviceBaseAddr /home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/Board/boardEnv/mvBoardEnvLib.c 1191 scott test NAND ADDRESS = f6000000,/home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/USP/mv_main.c 894 enter nand_probe cmd_nand.c 1658 NAND mfr id ec at cmd_nand.c 678 NAND id id 75 at cmd_nand.c 679 1 flash chips found. Total nand_chip size: 32 MB 0xf6000000: 32 MB devNum=1,mvBoardGetDeviceBaseAddr /home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/Board/boardEnv/mvBoardEnvLib.c 1191 scott test NAND ADDRESS = f8000000,/home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/USP/mv_main.c 900 enter nand_probe cmd_nand.c 1658 NAND mfr id ec at cmd_nand.c 678 NAND id id 75 at cmd_nand.c 679 1 flash chips found. Total nand_chip size: 32 MB 0xf8000000: 32 MB Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 500Mhz Orion 1 streaming disabled SysClock = 166Mhz , TClock = 166Mhz USB 0: host mode USB 1: host mode pciIfNum:2,/home/users/vicye/C2A9/uboot_c2a9/board/mv88fxx81/USP/mv_pci.c 628 PCI 0: PCI Express Root Complex Interface vendor id:0x11ab header_type:0x0, pci.c 471 PCI Scan: Found Bus 0, Device 0, Function 0 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x0, pci.c 471 PCI Scan: Found Bus 0, Device 1, Function 0 device id:0x6121, pci.c 479 CONFIG_PCI_PNP end at 502 in pci_hose_scan_bus PCI 1: Conventional PCI, speed = 33000000 vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 0 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 1 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 2 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 3 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 4 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 5 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 6 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x11ab header_type:0x80, pci.c 471 PCI Scan: Found Bus 1, Device 0, Function 7 device id:0x5182, pci.c 479 CONFIG_PCI_PNP vendor id:0x9413 header_type:0x0, pci.c 471 PCI Scan: Found Bus 1, Device 9, Function 0 device id:0x6010, pci.c 479 =pci.c 492 end at 502 in pci_hose_scan_bus i = 0 @@value = 243 i = 1 @@value = 243 i = 2 @@value = 243 i = 3 @@value = 243 i = 4 @@value = 243 i = 5 @@value = 243 i = 6 @@value = 243 i = 7 @@value = 243 i = 8 @@value = 255 i = 9 @@value = 255 i = 10 @@value = 255 i = 11 @@value = 255 i = 12 @@value = 255 i = 13 @@value = 255 i = 14 @@value = 255 i = 15 @@value = 255 video type = 1 Net: eth.c 133 egiga0 [PRIME] USB: scanning bus for devices... 1 USB Device(s) found scanning bus for storage devices... i=0 usb_get_dev_index i=0 usb_get_dev_index dev!=NULL iVendor 0 iProduct 0 devClass=9 IFClass=9 IFSubClass=0 i=1 usb_get_dev_index i=1 0 Storage Device(s) found Erasing Nand...Writing to Nand... done Hit any key to stop autoboot: 0 Using egiga0 device TFTP from server 10.4.50.5; our IP address is 10.4.50.165 Filename 'uImage'. Load address: 0x400000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### done Bytes transferred = 2288400 (22eb10 hex) ## Booting image at 00400000 ... Image Name: Linux-2.6.22.7 Created: 2011-01-19 4:23:53 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2288336 Bytes = 2.2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux................................................................................................................................................. done, booting the kernel. Linux version 2.6.22.7 (vicye@localhost.localdomain) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #58 Wed Jan 19 12:23:41 CST 2011 CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177 Machine: Feroceon Using UBoot passing parameters structure scott trace mac-> mvUbootVer:0x10c010f scott trace mac-> tag->u.mv_uboot.EthAddr:0xff:df:f7:ff:ff:ff scott trace mac->mvMacAddr:0xff:df:f7:ff:ff:ff scott clear mac->mvMacAddr:0x0:0:0:0:0:0 Memory policy: ECC disabled, Data cache writeback BUG: not creating mapping for 0x98000000 at 0x98000000 in user region BUG: not creating mapping for 0x40000000 at 0x40000000 in user region CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Built 1 zonelists. Total pages: 65024 Kernel command line: console=ttyS0,115200 root=/dev/nfs rw nfsroot=10.4.50.5:/mnt/ARM_FS/ ip=10.4.50.165:10.4.50.5:::DB88FXX81:egiga0:none PID hash table entries: 1024 (order: 10, 4096 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 128MB = 256MB total Memory: 255104KB available (4264K code, 275K data, 112K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 -------------------mvDevNandSet----------------- Sys Clk = 166666667, Tclk = 166666667 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 128MB SDRAM_CS1 ....base 08000000, size 128MB SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base 98000000, size 128MB PEX0_IO ....base f2000000, size 1MB PCI0_MEM ....base 40000000, size 1GB PCI0_IO ....base f2100000, size 1MB INTER_REGS ....base f1000000, size 1MB DEVICE_CS0 ....no such DEVICE_CS1 ....base f8000000, size 32MB DEVICE_CS2 ....no such DEV_BOOCS ....base f6000000, size 32MB CRYPT_ENG ....base f0000000, size 64KB Marvell Development Board (LSP Version 3.0.5_NAS_GDP_p8)-- RD-88F5182-NAS-3 Soc: 88F5182 A2 Detected Tclk 166666667 and SysClk 166666667 Marvell USB EHCI Host controller #0: c06ec600 Marvell USB EHCI Host controller #1: c06ec400 PCI: bus0: Fast back to back transfers disabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: orion_clocksource clocksource has been installed. IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered RTC registered cesadev_init(c000c61c) mvCesaInit: sessions=640, queue=64, pSram=f0000000 NTFS driver 2.1.28 [Flags: R/W]. JFFS2 version 2.2. (NAND) ĂŠ 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A Intel® PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright © 1999-2006 Intel Corporation. Marvell Ethernet Driver 'mv_ethernet': o Uncached descriptors in DRAM o DRAM SW cache-coherency o TCP segmentation offload enabled o Checksum offload enabled o Rx desc: 128 o Tx desc: 256 o Loading network interface 'egiga0' e100: Intel® PRO/100 Network Driver, 3.5.17-k4-NAPI e100: Copyright© 1999-2006 Intel Corporation PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ nand_dev_num=3 ---------NANDFLASH-------- baseLow=0xf6000000 baseHigh=0x0 size=0x2000000 enable=0x1 winNum=0x4 -------------------------- nand physaddr=0xf6000000 mv_mtd=0xcff21400 NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit) Scanning device for bad blocks Using static partition definition Creating 3 MTD partitions on "nand_mtd": 0x00000000-0x00100000 : "u-boot" 0x00100000-0x00400000 : "uImage" 0x00400000-0x02000000 : "file-system" nand_dev_num=3 ---------NANDFLASH-------- baseLow=0xf8000000 baseHigh=0x0 size=0x2000000 enable=0x1 winNum=0x6 -------------------------- nand physaddr=0xf8000000 mv_mtd=0xcff21000 NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit) Scanning device for bad blocks Using static1 partition definition Creating 1 MTD partitions on "nand_mtd1": 0x00000000-0x02000000 : "nandflash2" ehci_marvell ehci_marvell.4523: Marvell Orion EHCI ehci_marvell ehci_marvell.4523: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.4523: irq 17, io base 0xf1050100 ehci_marvell ehci_marvell.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_marvell ehci_marvell.167817: Marvell Orion EHCI ehci_marvell ehci_marvell.167817: new USB bus registered, assigned bus number 2 ehci_marvell ehci_marvell.167817: irq 12, io base 0xf10a0100 ehci_marvell ehci_marvell.167817: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid6: int32x1 20 MB/s raid6: int32x2 32 MB/s raid6: int32x4 37 MB/s raid6: int32x8 37 MB/s raid6: using algorithm int32x4 (37 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed arm4regs : 386.000 MB/sec 8regs : 272.000 MB/sec 32regs : 315.600 MB/sec raid5: using function: arm4regs (386.000 MB/sec) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com dm_crypt using the OCF package. Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC). usbcore: registered new interface driver snd-usb-audio usbcore: registered new interface driver snd-usb-caiaq ALSA device list: No soundcards found. oprofile: using timer interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 N Im = 0x1, P Im= 0x1, value = 0x8240 current phy impedance value = 0x4c0a egiga0: link down IP-Config: Guessing netmask 255.0.0.0 IP-Config: Complete: device=egiga0, addr=10.4.50.165, mask=255.0.0.0, gw=255.255.255.255, host=DB88FXX81, domain=, nis-domain=(none), bootserver=10.4.50.5, rootserver=10.4.50.5, rootpath= md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. Looking up port of RPC 100003/2 on 10.4.50.5 egiga0: link up, half duplex, speed 100 Mbps rpcbind: server 10.4.50.5 not responding, timed out Root-NFS: Unable to get nfsd port number from server, using default Looking up port of RPC 100005/1 on 10.4.50.5 rpcbind: server 10.4.50.5 not responding, timed out Root-NFS: Unable to get mountd port number from server, using default mount: server 10.4.50.5 not responding, timed out Root-NFS: Server returned error -5 while mounting /mnt/ARM_FS/ VFS: Unable to mount root fs via NFS, trying floppy. VFS: Cannot open root device "nfs" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 1024 mtdblock0 (driver?) 1f01 3072 mtdblock1 (driver?) 1f02 28672 mtdblock2 (driver?) 1f03 32768 mtdblock3 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) ....here it stuck Any ideas? it is possible that the boot file is not 100% compatible (not found exactly for SEB5108Lite .. just found for SEB 5108/5116 and SEB 5108H/5116H -- ) Share this post Link to post Share on other sites
Trafic 0 Posted August 29, 2016 Trying to solve the problem, I installed a program named FreeNFS (It seems to work with Windows 8.1 - my laptop OS) and it changed something..... Looking up port of RPC 100003/2 on 10.4.50.5 egiga0: link up, half duplex, speed 100 Mbps call_verify: server 10.4.50.5 requires stronger authentication. Root-NFS: Unable to get nfsd port number from server, using default Looking up port of RPC 100005/1 on 10.4.50.5 call_verify: server 10.4.50.5 requires stronger authentication. Root-NFS: Unable to get mountd port number from server, using default Does anyone know how I can pass the stronger authentication ? Thanks Share this post Link to post Share on other sites
Trafic 0 Posted August 31, 2016 Hello It looks like I "killed" for good now... In the absence of suggestions i tried all commands of u-Boot until to this two.. bubt - Burn an image on the Boot Nand Flash. file-name Burn a binary image on the t Nand Flash, default file-name is u-boot.bin . bubt_vic- Burn an image on the Boot Nand Flash By Vic. file-name Burn a binary image on the Boot Flash. After run the (bubt_vic) I froze and leds which indicating the presence Hdd lights up (Although no hdd connected)... Tried reset (buttons not working) disconnected from power supply.. nothing... just LEDs are on... no more connection via serial (for PuTTY) or network for Tftpd32. I believe that the only solution would be a JTAG connection via a cable Jtag to LPT (to flash NAND) ..but I do not know the procedure and what programs to use.. Some help please... Share this post Link to post Share on other sites
tomcctv 190 Posted August 31, 2016 Hi once you get the test colour screen was the time it gave up. You Will not find anything on dvr to allow you to restart. You will need the software reloaded but it is not worth it and no longer supported. We're are you located ? Share this post Link to post Share on other sites
Trafic 0 Posted August 31, 2016 Hi..I'm from Romania.. I'm sure that can be reset via Jtag, but it is complicate and not have the necessary files and Jtag interface..I know.. Share this post Link to post Share on other sites
tomcctv 190 Posted August 31, 2016 Hi..I'm from Romania..I'm sure that can be reset via Jtag, but it is complicate and not have the necessary files and Jtag interface..I know.. No it can't ..... And 100% it needs a reflash With you already taking it back to test screen .... It has nothing recoverable. Share this post Link to post Share on other sites
