"Alarm Event: No disk" on IPC-EBW81200

[fa355115 1]

Hi there,

I have recently installed an IPC-EBW81200 with a 64 Gb SD card into int I am using for recording (on internal SD card) based on motion detection.

 

Quite often, I have a notification about "Alarm Event: No disk" then few seconds after a "Alarm Event: No diskStop", like if the SD card was removed or not detected anymore.

 

Here is the lof the camera is providing ... do you have the same issue or not and do you know where thic can come from ??

 

Most of the time it then continues to record, but sometimes the card gots into "Failed" status and I need to format it through the interface then it goes again for some time ... very annoying ...

 

... see lines 346 and 347

 

332    System    2016-11-23 06:24:28    Event End    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
333    System    2016-11-23 06:24:19    Event Begin    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
334    System    2016-11-23 06:09:45    Event End    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
335    System    2016-11-23 06:09:31    Event Begin    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
336    System    2016-11-23 06:01:59    Hot swap    {"Action":"Insert Device","Device Name":"Disk1"}
337    System    2016-11-23 06:01:56    Save Configuration    {"Name":"Network Config"}
338    System    2016-11-23 06:01:49    Save Configuration    {"Name":"Encode"}
339    System    2016-11-23 06:01:49    Save Configuration    {"Name":"Encode"}
340    System    2016-11-23 06:01:48    Start up    {"Reboot Mark":"Abort"}
341    System    2016-11-23 06:01:48    Abort    {"Time":"2016-11-23 06:01:20"}
342    System    2016-11-23 05:57:30    Start up    {"Reboot Mark":"Abort"}
343    System    2016-11-23 05:57:30    Abort    {"Time":"2016-11-23 05:57:01"}
344    System    2016-11-23 05:53:58    Start up    {"Reboot Mark":"Abort"}
345    System    2016-11-23 05:53:58    Abort    {"Time":"2016-11-23 05:53:30"}
346    System    2016-11-23 05:45:20    Hot swap    {"Action":"Insert Device","Device Name":"Disk1"}
347    System    2016-11-23 05:45:15    Hot swap    {"Action":"Remove Device","Device Name":"Disk1"}
348    System    2016-11-23 05:33:48    Event End    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
349    System    2016-11-23 05:33:38    Event Begin    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
350    System    2016-11-23 05:08:09    Event End    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}
351    System    2016-11-23 05:08:00    Event Begin    {"Channel NO.":1,"Event Type":"Motion Detect","Region Name":["Region1"]}

 

Many Thanks !

[Island Boy 0]

Do you use a UPS (Uninterruptible power supply)?

[fa355115 1]

Camera is powered via PoE on my switch and I have a NAS as well connected on on UPS (the switch is also connected to the UpS)

Why ?

[Island Boy 0]

From your reply I guess it's not important. Power failures would mess up my hard drive & I would have to use a partition tool (surface read) to fix it......sorry, I don't think I will be of any help to you.