cjbreto 0 Posted October 10, 2018 Following on from my previous post regarding IR/Night mode switching issues I’ve now replaced all power supplies (Have 5 separted 5A power supplies powering 8 cameras). Changed all baluns and power connections, removed the cat 5 wiring and replaced with leads supplied with the kit and still have the same problems. Cameras switching to night mode and not switching back to day mode. Some not switching to night mode at all. I’ve now found that I unplug each camera then power back up they instantly switch to the correct mode (Daylight/night mode). This is happening intermittently across the majority of cameras. I’ve literally changed everything except the cameras themselves and the DVR. Is this likely to be a camera issue? As they aren’t switching over unless unplugged then re-energised. Share this post Link to post Share on other sites
tomcctv 190 Posted October 10, 2018 Following on from my previous post regarding IR/Night mode switching issues I’ve now replaced all power supplies (Have 5 separted 5A power supplies powering 8 cameras). Changed all baluns and power connections, removed the cat 5 wiring and replaced with leads supplied with the kit and still have the same problems. Cameras switching to night mode and not switching back to day mode. Some not switching to night mode at all. I’ve now found that I unplug each camera then power back up they instantly switch to the correct mode (Daylight/night mode). This is happening intermittently across the majority of cameras. I’ve literally changed everything except the cameras themselves and the DVR. Is this likely to be a camera issue? As they aren’t switching over unless unplugged then re-energised. What type of baluns did you replace with What size cable did you use and how did you wire video and power ? I would also reply to your posts rather than starting a new post every time Share this post Link to post Share on other sites
cjbreto 0 Posted October 10, 2018 Following on from my previous post regarding IR/Night mode switching issues I’ve now replaced all power supplies (Have 5 separted 5A power supplies powering 8 cameras). Changed all baluns and power connections, removed the cat 5 wiring and replaced with leads supplied with the kit and still have the same problems. Cameras switching to night mode and not switching back to day mode. Some not switching to night mode at all. I’ve now found that I unplug each camera then power back up they instantly switch to the correct mode (Daylight/night mode). This is happening intermittently across the majority of cameras. I’ve literally changed everything except the cameras themselves and the DVR. Is this likely to be a camera issue? As they aren’t switching over unless unplugged then re-energised. What type of baluns did you replace with What size cable did you use and how did you wire video and power ? I would also reply to your posts rather than starting a new post every time I’ve used pre terminated BNC cable which was supplied with the kit. Same issue as the CAT5. Cameras are either switching to nightvision and stuck in that mode when it’s daylight until I unplug and plug back together they switch instantly back to day mode. Same scenario at night with other cameras . Camera won’t go to nightvision until I unplug then plug back - goes straight to night mode. As I say only thing I haven’t changed is the cameras themselves and the DVR Apologies will do that in future. Share this post Link to post Share on other sites
emmagreen99 0 Posted October 12, 2018 Best of luck bro... Share this post Link to post Share on other sites
cjbreto 0 Posted October 29, 2018 This turned out to be faulty/cheap GOVISION cameras. AVOID at all cost! I literally replaced all cabling and changed balun connections 3/4 times, wasted hours and hours of labour doing this to find out Id been sold cheap cameras under the advert of Hikvision. Replaced all cameras and all working in night and day! However one camera is condensating from the inside of the lens and customer won’t pay up. I’ve opened camera and made sure all seals are tight and correct still condensating! I’m fed up of this job now its been a nightmare Share this post Link to post Share on other sites
tomcctv 190 Posted October 29, 2018 labour doing this to find out Id been sold cheap cameras under the advert of Hikvision. Well I can guarantee you bought cheap nasty geovision China copies. And hik has nothing to do with geovision Share this post Link to post Share on other sites
MichaelHarris259 0 Posted November 1, 2018 I think there is a hardware problem with your cameras... Share this post Link to post Share on other sites
