fred2021 0 Posted April 16, 2021 Have been asked to get a CCTV system working again where I have moved to. It was installed about 6 years ago and I replaced the PSU and it's now OK. I thought I should update the password but now can't log in. The system is mounted on a high shelf (very clumsy) and only has mouse input - should have written the password down before inputting it... No amount of trying variations has succeeded. Anyway, can someone kindly supply what I understand is called a "password of the day". The date/time shown on the recorder is GMT + 1 and is current - i.e. this was posted at 19h00 on 16 April 2021 (not sure which time zone members are in). Share this post Link to post Share on other sites
tomcctv 190 Posted April 16, 2021 Hi. 160768 is the password switch off your unit for 20 minutes before you enter the code Share this post Link to post Share on other sites
fred2021 0 Posted April 17, 2021 Thanks very much for the reply. I think that you were "too quick" for me as I checked before going to bed but no reply. Logged in this morning but the password you supplied was invalid. Might I ask for you to do it again for Saturday? I'll be logged in for the next 12 hours. Share this post Link to post Share on other sites
tomcctv 190 Posted April 17, 2021 444616 is today’s code Share this post Link to post Share on other sites
fred2021 0 Posted April 17, 2021 tomcctv - thanks for providing today's code. Sadly, the box says "invalid password". Yes I did have the box turned off for 30 mins before starting it up. So not sure what to do next - apart from buying another box... The distributor will only issue a password to those with a trade account. Telephoning several installers say the same thing - you don't have an account with us so we won't help. One installer was quite helpful though in that he said we don't have an office but we send people on-site. However, the "manufacturers" don't respond straight away - we often have to wait a couple of hours. Paying for a service like this is getting close to the cost of a replacement box. Once again, thanks for the time and effort you have put in. Share this post Link to post Share on other sites
tomcctv 190 Posted April 17, 2021 420524 is for the i-Apollo vs 3.2 update Share this post Link to post Share on other sites
fred2021 0 Posted April 17, 2021 Thanks for the swift reply. The box says "no" to this one. Have attached three photos - box 1 is from when I could get in (I was extracting vids of unwanted visitors) and box 2 is from just now. Box 3 is the back of the unit. Might this help in working out a password? Otherwise, thanks again for being so helpful. Share this post Link to post Share on other sites
tomcctv 190 Posted April 17, 2021 692064 that’s the dahua lite 960h dvr ..... you might have to try a few codes ... try the above one Share this post Link to post Share on other sites
fred2021 0 Posted April 17, 2021 Thanks for the 692064 - invalid password. Any other codes up your sleeve? Share this post Link to post Share on other sites
tomcctv 190 Posted April 17, 2021 1 minute ago, fred2021 said: Thanks for the 692064 - invalid password. Any other codes up your sleeve? Yes a few more just logged into dahua ftp YMR9OM1201 case sensitive ... O is letter 0 is number Share this post Link to post Share on other sites
fred2021 0 Posted April 17, 2021 That caused the box to reboot - well done. No password needed to get in and I can see the last set of recordings. Phew... So, thanks once again and appreciate you have been "working" on a Saturday. My wife has said "dinner ready" so need to go. Share this post Link to post Share on other sites
tomcctv 190 Posted April 17, 2021 Hi. Just remember to create a new password before midnight or you will have to start again your system is called pioneer (dahua lite) Share this post Link to post Share on other sites
fred2021 0 Posted April 17, 2021 Timely advice. Over dinner, it struck me that the carriage could turn back into a pumpkin if I didn't put in a password tonight. So thanks for the reminder. All done and checked three times plus a note made of the password. I've also made a note of the correct box name (it appears to be rebadged) so were something ever to occur again, then no time would be wasted. To summarise, all is well and thanks to both you and the cctvforum for sorting it out so succesfully and without any drama (though my heart did leap when the box rebooted...). Lastly, the joint owners of the building are thinking about upgrading the cameras and box (not this year though) so as to have higher definition. Having been able to get the box going again after fitting a new PSU meant we could identify how the low life was getting into the building and hence what was needed to make the building more secure. The definition is a bit low for mug shots but we had a stroke of luck. One owner and his buddy were coming back into the building after walking their big dog around midnight. Seems they surprised themselves and the low life who were smoking exotic cheroots in the lower lobby. The video showed the uninivited guests running out never to come back... Share this post Link to post Share on other sites
tomcctv 190 Posted April 17, 2021 Hi the updated version of that system is one of the best out there at the moment and not expensive and you can still use your existing cameras and add upto 8mp you might find the images will be better once you have burned them off or view them on the app (explorer) Share this post Link to post Share on other sites
bernardand 0 Posted May 2, 2021 Sadly, the box says "invalid password". Yes I did have the box turned off for 30 mins before starting it up. Share this post Link to post Share on other sites
tomcctv 190 Posted May 2, 2021 1 hour ago, bernardand said: Sadly, the box says "invalid password". Yes I did have the box turned off for 30 mins before starting it up. No point jumping into posts which system do you have Share this post Link to post Share on other sites
